Electric 2 (Rapid 2) / Scrambler 2 Controls; Using The Handbike Batec Electric Uad Mini 2 / Electric 2 (Rapid 2) / Scrambler 2 Controls - BATEC MINI 2 Manual De Usuario

IMPORTANT!
For the safety chec to be completed properly, the heel of the HAND-
BIKE BATEC ELECTRIC must be stopped and the user must have squeezed
the brake levers on the HANDBIKE BATEC ELECTRIC at least once.
• Turn o : Turn the ey on the battery anti cloc
sition. If you leave it in the OPEN position, your HANDBIKE BATEC
ELECTRIC ill be o and the battery ill be ready to remove.
• Speed up: The throttle is on the right grip on the handlebar. It or s
just li e a motorbi e, meaning you can regulate your speed by turn-
ing the throttle on the grip.
( ee fig. 23)
• Brake: The HANDBIKE BATEC ELECTRIC has two brake levers on the
handlebar that activate the disc bra es. Squeeze the lever to acti-
vate the brakes. Advice: Use one hand to accelerate and the other to
bra e. Advice: Al ays eep t o fingers on the bra e lever in order to
respond quic ly. Pressing on the bra e lever and the red lever at the
same time bloc s the bra e lever, acting as a par ing bra e.
• Front and back gears:
There are t o operating modes: Front and bac gears:
In front gear, there are speed limits (position 1, position 2 and
position ), each ith a light indicator on the display panel.
- In back gear, there is only one speed and one light indicator on the
display panel.
hen the HANDBIKE BATEC ELECTRIC is s itched on, it ill al ays
be in front gear, position 1.
In front gear, press button F to choose the desired speed limit (po-
sition 1, position 2 or position ).
Press the R button to s itch to bac gear. This mode ill only be acti-
vated if the HANDBIKE BATEC ELECTRIC is sopped and the throttle is
not engaged. Press the F button to switch back to front gear.
– 26 –
ise to the OFF po-
( ee fig. 22)
( ee fig. 24)
( ee fig. 25)
• Free heel mode: To use the HANDBIKE BATEC ELECTRIC in free-
heel mode:
S itch the device o ith the ey.
To move for ards or bac ards, use the rims on the
to move the HANDBIKE BATEC ELECTRIC and heelchair in the de-
sired direction.
- To turn, turn the HANDBIKE BATEC ELECTRIC with one hand while
propelling the wheelchair with the other.
To stop, use the HANDBIKE BATEC ELECTRIC bra es or the rim on
the wheelchair.
• Lights: There is a button on the HANDBIKE BATEC ELECTRIC handlebar
to s itch on the front and rear lights.
front light ill go on in normal mode and the light indicator on the dis-
play panel ill turn green. hen you push the front light button again,
it changes to high beam mode, and so on. To turn o the lights, hold
the button down for 2 seconds. The front light is below the battery and
the t o rear lights, on either side of the stand frame.
4.7. USING THE HANDBIKE BATEC ELECTRIC UAD MINI 2 /

ELECTRIC 2 (RAPID 2) / SCRAMBLER 2 CONTROLS

• You can find out the meaning of all the symbols used on the controls
of the BATEC ELECTRIC HANDBIKE in Figure 58.
• Turn on: Turn the key on the right side of the battery clockwise to the
ON position. It ill do a system chec : don t start using your HAND-
BIKE BATEC ELECTRIC until it has finished ith the system chec and
all the lights are on.
( ee fig. 27)
• Turn o : Turn the ey on the battery anti cloc
sition. If you leave it in the OPEN position, your HANDBIKE BATEC
ELECTRIC ill be o and the battery ill be ready to remove.
• Speed up: Pull the HANDBIKE BATEC ELECTRIC
bar towards you to activate the throttle.
– 27 –
heelchair
hen you push the button, the
( ee fig. 26a, 26b, 26c)
ise to the OFF po-
( ee fig. 27)
UAD MINI handle-
( ee fig. 28)