Machine Safety; Description, Specifications And Standard Equipment Description; Specifications - Ridgid Kollmann K-75A/B Manual Del Usuario

Kollmann
WARNING
Cables may twist or kink. Fingers, hands or other
body parts can be crushed or broken.
• Wear mittens with rivets
• Do not use with damaged or worn electrical cords.
• Keep guards in place.
• Place machine close to inlet.
• Plug cord into grounded three-prong receptacle.
• Wear safety glasses.
• Test Ground Fault Circuit Interrupter (GFCI) to insure
proper operation.
READ ABOVE WARNING CAREFULLY!

Machine Safety

1. Wear standard equipment glove provided with
the machine. Never grasp a rotating cable with a
cloth or loose fitting glove. It could get wrapped
around the cable and cause serious injury.
2. Never operate machine with belt guard removed.
Fingers can be caught between the belt and pulley.
3. Do not overstress cables. Keep one hand on the
cable for control when the machine is running.
Overstressing cables because of obstruction may
cause twisting or kinking and result in serious injury.
4. Position machine within two feet of inlet. Use
Front End Guide Hose when it is difficult to locate
the machine near the access or clean out. Greater
distances can result in cable twisting or kinking.
5. Do not operate machine in (REV) reverse. Oper-
ating machine in reverse can result in cable damage
and is used only to back tool out of an obstruction.
6. Operate machine from the side with the
FOR/OFF/REV Switch. Allows for better control of
the machine.
7. Use Rear Guide Hose. Prevents cable from whipping
and picking up debris.
4
K-75A/B, K-1500A/B, & K-1500SP Drain Cleaning Machines
Ridge Tool Company • Elyria, Ohio • U.S.A.
8. Be careful when cleaning drains where cleaning
compounds have been used. Avoid direct contact
with skin and eyes. Serious burns can result from
some drain cleaning compounds.
9. Machine is made to clean drain lines. Follow in-
structions in operator's manual on machine uses.
Other uses may increase the risk of injury.
10. Do not use if clutch, ON/OFF Switch, ground plug
or GFCI are broken. Poorly maintained tools can
result in serious injury.
SAVE THESE INSTRUCTIONS!
Description, Specifications and
Standard Equipment
Description
The RIDGID/Kollmann K-75A/B, K-1500A/B & K-1500SP
Drain Cleaning Machines are for cleaning 1
10" lines. These machines may be used for most appli-
cations requiring power cleaning. A powerful reversible
electric motor coupled with an instant acting clutch permits
complete and immediate response in any situation.
K-75 machines come equipped to run
2" – 4" lines through 175'. They can be easily adapted to
use 5/8" cable 1 1 / " to 3" lines through 125'.
4
K-1500 machines come equipped to run 1
clean 3" – 10" lines through 200' — the 1500SP through
300'. They can be easily adapted to use
clean 2" – 4" lines through 175'.

Specifications

Clutch...........................Instant Acting
Motor:
K-75A/B .......................
K-1500A/B ................
K-1500A/B-SP ............1HP, 115V-240V/50-60 Hz,
1 / " through
4
7 / " cable to clean
8
/ " cable to
1
4
7 / " cable to
8
1 / HP, 115V/60Hz, single
2
phase, AC, induction, re-
versible with toggle switch.
3 / HP, 115V/60Hz, single
4
phase, AC, induction, re-
versible with toggle switch.
(NOTE: 230-240V/50 Hz ver-
sions available upon request.)
single phase, AC, induction,
Totally enclosed/fan cooled,
reversible with rotary switch.