Woods DS8.30E Manual Del Operador página 5


Your dealer can supply original equipment hydraulic accessories and
repair parts. Substitute parts may not meet original equipment specifications
and may be dangerous.

Never go underneath equipment (lowered to the ground or raised) unless
it is properly blocked and secured. Never place any part of the body under-
neath equipment or between movable parts even when the engine has been
turned off. Hydraulic system leak down, hydraulic system failures, mechanical
failures, or movement of control levers can cause equipment to drop or rotate
unexpectedly and cause severe injury or death. Follow Operator's Manual
instructions for working underneath and blocking requirements or have work
done by a qualified dealer.

Make sure attachment is properly secured, adjusted, and in good operat-
ing condition.
 Make sure spring-activated locking pin or collar slides freely and is seated
firmly in tractor PTO spline groove.

Make sure attachment is properly secured, adjusted, and in good operat-
ing condition.

Make sure all safety decals are installed. Replace if damaged. (See Safety
Decals section for location.)

Keep children and bystanders away from storage area.

Do not disconnect hydraulic lines until machine is securely blocked or
placed in lowest position and system pressure is released by operating valve
levers.

Explosive separation of tire and rim parts can cause serious injury or
death. Release all air pressure before loosening bolts on wheel.
STORAGE

Leak down or failure of mechanical or hydraulic system can cause equip-
ment to drop.

Frequently check blades. They should be sharp, free of nicks and cracks,
and securely fastened.

Never direct discharge toward people, animals, or property.

Operate only in daylight or good artificial light.

Keep hands, feet, hair, and clothing away from equipment while engine is
running. Stay clear of all moving parts.

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.

Power unit must be equipped with ROPS or ROPS cab and seat belt.
Keep seat belt securely fastened. Falling off power unit can result in death from
being run over or crushed. Keep foldable ROPS system in "locked up" position
at all times.

Look down and to the rear and make sure area is clear before operating in
reverse.
DS8 & 10 CE Export Safety Rules (3/27/2017)
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Do not operate or transport on steep slopes.

Do not stop, start, or change directions suddenly on slopes.

Use extreme care and reduce ground speed on slopes and rough terrain.

Watch for hidden hazards on the terrain during operation.

Stop power unit and equipment immediately upon striking an obstruction.
Turn off engine, remove key, inspect, and repair any damage before resuming
operation.

Leak down or failure of mechanical or hydraulic system can cause equip-
ment to drop.

Do not modify or alter or permit anyone else to modify or alter the equip-
ment or any of its components in any way.

Always wear relatively tight and belted clothing to avoid getting caught in
moving parts. Wear sturdy, rough-soled work shoes and protective equipment
for eyes, hair, hands, hearing, and head; and respirator or filter mask where
appropriate.

Keep all persons away from operator control area while performing adjust-
ments, service, or maintenance.

Make certain all movement of equipment components has stopped before
approaching for service.

Do not handle blades with bare hands. Careless or improper handling may
result in serious injury.

Your dealer can supply genuine replacement blades. Substitute blades
may not meet original equipment specifications and may be dangerous.

Tighten all bolts, nuts, and screws to torque chart specifications. Check
that all cotter pins are installed securely to ensure equipment is in a safe condi-
tion before putting unit into service.

Make sure all safety decals are installed. Replace if damaged. (See Safety
Decals section for location.)

Make sure shields and guards are properly installed and in good condition.
Replace if damaged.

Follow manual instructions for storage.
O :
N MOUNTED CUTTERS

Disconnect cutter driveshaft and secure up off ground. Raise cutter with 3-
point hitch. Place blocks under cutter side skids. Lower cutter onto blocks. Dis-
connect cutter from tractor 3-point hitch and carefully drive tractor away from
cutter.
O - :
N PULL TYPE CUTTERS

Raise cutter and block securely. Block wheels and raise tongue with jack.
Disconnect hydraulic lines to cylinder. Disconnect driveline and secure up off
the ground.
Safety 5