Safety Rules - Woods DS8.30E Manual Del Operador

Safety is a primary concern in the design and manufacture of our products.
Unfortunately, our efforts to provide safe equipment can be wiped out by an
operator's single careless act.
In addition to the design and configuration of equipment, hazard control and
accident prevention are dependent upon the awareness, concern, judge-
ment, and proper training of personnel involved in the operation, transport,
maintenance, and storage of equipment.
It has been said, "The best safety device is an informed, careful operator."
We ask you to be that kind of operator.
TRAINING

Safety instructions are important! Read all attachment and power unit
manuals; follow all safety rules and safety decal information. (Replacement
manuals and safety decals are available from your dealer. To locate your near-
est dealer, check the Dealer Locator at www.WoodsEquipment.com, or call 1-
815-732-9509 plus the appropriate international dialing code for the USA.)
Failure to follow instructions or safety rules can result in serious injury or death.

If you do not understand any part of this manual and need assistance, see
your dealer.

Know your controls and how to stop engine and attachment quickly in an
emergency.

Do not put this equipment into service unless all side skids are properly
installed and in good condition. Replace if damaged.
PREPARATION

If equipped with driveline guard tether chains, make sure they are
attached to the tractor and equipment as shown in the pamphlet that accompa-
nies the driveline. Replace if damaged or broken. Check that driveline guards
rotate freely on driveline before putting equipment into service.

Inspect chain shielding before each use. Replace if damaged.

Make sure shields and guards are properly installed and in good condi-
tion. Replace if damaged.

Operators must be instructed in and be capable of the safe operation of
the equipment, its attachments, and all controls. Do not allow anyone to oper-
ate this equipment without proper instructions.

Do not allow bystanders in the area when operating, attaching, removing,
assembling, or servicing equipment.

A minimum 25% of tractor and equipment weight must be on the tractor
front wheels when attachments are in transport position. Without this weight,
front tractor wheels could raise up resulting in loss of steering. The weight may
be attained with front wheel weights, ballast in tires, front tractor weights or
front loader. Weigh the tractor and equipment. Do not estimate.

Connect PTO driveline directly to power unit PTO shaft. Never use
adapter sleeves or adapter shafts. Adapters can cause driveline failures due to
incorrect spline or incorrect operating length and can result in personal injury
or death.
OPERATION

Full chain shielding must be installed at all times. Thrown objects could
injure people or damage property.
• If the machine is not equipped with full chain shielding, operation
must be stopped.
• This shielding is designed to reduce the risk of thrown objects. The
mower deck and protective devices cannot prevent all objects from escap-
ing the blade enclosure in every mowing condition. It is possible for
objects to ricochet and escape, traveling as much as 300 feet (92m).

Always sit in power unit seat when operating controls or starting engine.
Securely fasten seat belt, place transmission in neutral, engage brake, and
ensure all other controls are disengaged before starting power unit engine.

Do not operate or transport equipment while under the influence of alcohol
or drugs.

Inspect and clear area of stones, branches, or other hard objects that
might be thrown, causing injury or damage.

Before performing any service or maintenance, disconnect driveline from
tractor PTO.

Operate tractor PTO at 540 RPM. Do not exceed.
4 Safety

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
TRANSPORTATION

The maximum transport speed for towed machines is 20 mph (32 km/h).
Regardless of the maximum speed capability of the towing tractor, do not
exceed the implement's maximum transport speed. Doing so could result in:
• Loss of control of the implement and tractor
• Reduced or no ability to stop during braking
• Implement tire failure
• Damage to the implement or its components.

Use additional caution and reduce speed when under adverse surface
conditions, turning, or on inclines.

Never tow this implement with a motor vehicle.

Do not operate PTO during transport.

Do not operate or transport on steep slopes.

Do not operate or transport equipment while under the influence of alcohol
or drugs.

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.
MAINTENANCE

Never allow children or untrained persons to operate equipment.

Check that all hardware is properly installed. Always tighten to torque
chart specifications unless instructed otherwise in this manual.

Keep hands and body away from pressurized lines. Use paper or card-
board, not hands or other body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate skin and will cause serious
injury or death.

Do not allow bystanders in the area when operating, attaching, removing,
assembling, or servicing equipment.

Before working underneath, raise mower, install transport lock, and block
mower securely. Hydraulic system leak down and failure of mechanical or
hydraulic system can cause equipment to drop.

Make sure that all operating and service personnel know that if hydraulic
fluid penetrates skin, it must be surgically removed as soon as possible by a
doctor familiar with this form of injury or gangrene, serious injury, or death will
result. CONTACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR
EYES. DO NOT DELAY.

Air in hydraulic systems can cause erratic operation and allows loads or
equipment components to drop unexpectedly. When connecting equipment or
hoses or performing any hydraulic maintenance, purge any air in hydraulic sys-
tem by operating all hydraulic functions several times. Do this before putting
into service or allowing anyone to approach the equipment.

Power unit must be equipped with ROPS or ROPS cab and seat belt.
Keep seat belt securely fastened. Falling off power unit can result in death from
being run over or crushed. Keep foldable ROPS system in "locked up" position
at all times.

Make sure all hydraulic hoses, fittings, and valves are in good condition
and not leaking before starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses must not be twisted, bent
sharply, kinked, frayed, pinched, or come into contact with any moving parts.
Operate moveable components through full operational range to check clear-
ances. Replace any damaged hoses immediately.

Remove accumulated debris from this equipment, power unit, and engine
to avoid fire hazard.

Always wear relatively tight and belted clothing to avoid getting caught in
moving parts. Wear sturdy, rough-soled work shoes and protective equipment
for eyes, hair, hands, hearing, and head; and respirator or filter mask where
appropriate.
 Before dismounting power unit or performing any service or maintenance,
follow these steps: disengage power to equipment, lower the 3-point hitch and
all raised components to the ground, operate valve levers to release any
hydraulic pressure, set parking brake, stop engine, remove key, and unfasten
seat belt.
DS8 & 10 CE Export Safety Rules (3/27/2017)