Tabla de contenido
Idiomas disponibles
Idiomas disponibles
have it installed. Damaged products cause
risks for your safety.
Make sure that the water inlet and discharge
C
hoses as well as the power cable are not
folded, pinched or crushed while pushing
the product into its place after installation or
cleaning procedures.
Appropriate installation location
•
Place the machine on a rigid floor. Do not
place it on a long pile rug or similar surfaces.
•
Total weight of the washing machine and the
dryer -with full load- when they are placed
on top of each other reaches to approx.
180 kilograms. Place the product on a solid
and flat floor that has sufficient load carrying
capacity!
•
Do not place the product on the power cable.
•
Do not install the product at places where
temperature may fall below 0ºC.
•
Place the product at least 1 cm away from
the edges of other furniture.
Removing packaging reinforcement
Tilt the machine backwards to remove the
packaging reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
Removing the transportation locks
Do not remove the transportation locks before
A
taking out the packaging reinforcement.
Remove the transportation safety bolts before
A
operating the washing machine, otherwise,
the product will be damaged.
1. Loosen all the bolts with a spanner until they
rotate freely (C).
2. Remove transportation safety bolts by turning
them gently.
3. Attach the plastic covers supplied in the User
Manual bag into the holes on the rear panel.
(P)
Keep the transportation safety bolts in a safe
C
place to reuse when the washing machine
needs to be moved again in the future.
Never move the product without the
C
transportation safety bolts properly fixed in
place!
Connecting water supply
The water supply pressure required to run
C
the product is between 1 to 10 bars (0.1 – 10
MPa). It is necessary to have 10 – 80 liters of
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
If you are going to use the double water-inlet
C
product as a single (cold) water-inlet unit, you
must install the supplied stopper to the hot
water valve before operating the product.
(Applies for the products supplied with a blind
stopper group.)
If you want to use both water inlets of the
C
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
supplied with a blind stopper group.)
Models with a single water inlet should not
A
be connected to the hot water tap. In such
a case the laundry will get damaged or the
product will switch to protection mode and
will not operate.
Do not use old or used water inlet hoses on
A
the new product. It may cause stains on your
laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product.
Red hose (left) (max. 90 ºC) is for hot water
inlet, blue hose (right) (max. 25 ºC) is for cold
water inlet.
Ensure that the cold and hot water
A
connections are made correctly when
installing the product. Otherwise, your laundry
will come out hot at the end of the washing
process and wear out.
2. Tighten all hose nuts by hand. Never use a
wrench when tightening the nuts.
3. Open the taps completely after making the
hose connection to check for water leaks at
the connection points. If any leaks occur, turn
off the tap and remove the nut. Retighten
the nut carefully after checking the seal. To
prevent water leakages and damages caused
by them, keep the taps closed when the
machine is not in use.
Connecting to the drain
•
The end of the drain hose must be directly
connected to the wastewater drain or to the
washbasin.
Your house will be flooded if the hose comes
A
out of its housing during water discharge.
3
EN
Tabla de contenido
