Prior To Operation - DeWalt DWE7492 Traducido De Las Instrucciones Originales

EnGLIsh
not the 82.5 cm rip position. The white scale (bottom)
reads correctly only when the fence is mounted on the
right side of the blade and in position 2 (for 20.3 cm to
82.5 cm ripping).
The rip scale reads correctly only when the fence is mounted to
the right of the blade.
Rail Lock Adjustment (Fig. A, K)
The rail lock has been factory-set. If you need to re-adjust,
proceed as follows:
1. Lock the rail lock lever 5 .
2. On the underside of the saw, loosen the jam nut
3. Tighten the hex rod 34 until the spring on the locking
system is compressed creating the desired tension on the
rail lock lever. Retighten the jam nut against the hex rod.
4. Flip the saw over and check that the fence does not move
when the lock lever is engaged. If the fence is still loose,
tighten the spring further.
Bevel Stop and Pointer Adjustment (Fig. L)
1. Raise the blade fully by rotating the blade height
adjustment wheel 6 clockwise until it stops.
2. Unlock the bevel lock lever
right. Loosen the bevel stop screw
3. Place a square flat against the table top and against the
blade between teeth. Ensure the bevel lock lever is in its
unlocked, or up position.
4. Using the bevel lock lever, adjust the bevel angle until the
blade is flat against the square.
5. Tighten the bevel lock lever by pushing it down.
6. Turn the bevel stop cam 35
bearing block. Tighten the bevel stop screw
7. Check the bevel angle scale. If the pointer does not read 0°,
loosen pointer screw and move the pointer so it reads
37
correctly. Retighten the pointer screw.
8. Repeat at 45°, but do not adjust pointer.
Mitre Gauge Adjustment (Fig. A)
To adjust mitre gauge 10 loosen knob, set to desired angle and
tighten knob.
Body and Hand Position
Proper positioning of your body and hands when operating the
table saw will make cutting easier, more accurate and safer.

WARNING:
• Never place your hands near the cutting area.
• Place your hands no closer than 150 mm from
the blade.
• Do not cross your hands.
• Keep both feet firmly on the floor and maintain
proper balance.
48
.
33
by pushing it up and to the
7
36 .
until it firmly contacts the
36 .

Prior to Operation


WARNING:
• Install the appropriate saw blade. Do not use
excessively worn blades.The maximum rotation speed
of the tool must not exceed that of the saw blade.
• Do not attempt to cut excessively small pieces.
• Allow the blade to cut freely. Do not force.
• Allow the motor to reach full speed before cutting.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The attention of UK users is drawn to the "woodworking
machines regulations 1974" and any subsequent amendments.
Ensure the machine is placed to satisfy your ergonomic
conditions in terms of table height and stability. The machine
site shall be chosen so that the operator has a good overview
and enough free surrounding space around the machine that
allows handling of the workpiece without any restrictions.
To reduce effects of increased vibration, make sure the
environment is not too cold, the machine and accessory are well
maintained and the workpiece size is suitable for this machine.

WARNING:
• Ensure the machine is placed to satisfy ergonomic
conditions in terms of table height and stability. The
machine site shall be chosen so that the operator
has a good overview and enough free surrounding
space around the machine that allow handling of the
workpiece without any restrictions.
• Install the appropriate saw blade. Do not use
excessively worn blades. The maximum rotation speed
of the tool must not exceed that of the saw blade.
• Do not attempt to cut excessively small pieces.
• Allow the blade to cut freely. Do not force.
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles
are tight.
• Never place either hand in the blade area when the
saw is connected to the electrical power source.
• Never use your saw for freehand cuts!
• Do not saw warped, bowed or cupped workpieces.
There must be at least one straight, smooth side to go
against the rip fence or mitre fence.
• Always support long workpieces to prevent kickback.
• Do not remove any cut-offs from the blade area while
the blade is running.