Sammic SL-1200BP Manual De Instrucciones página 8

T
HERMAL
Nº C ( ) D ºF ºC
YCLE S RAIN
L
19 60/120/180 1 0 1
20 60/120/180 1 0 1
21 60/120/180 1 1 0
22 60/120/180 1 1 0
Configuration Selection:
The machine configuration number appe-
ars on the display for 2 seconds once the
main switch is turned on. In order to select
another configuration number, proceed as
follows:
1.Power the machine down.
2.Move the two microswitches (Fig B-3) to
the ON position.
3.Power the machine up.
4.Press key (Fig B-5): the configuration
number is displayed.
5.Press "Start" (Fig A-5) to increment the
configuration number.
6.Press "Drain" (Fig A-7) to decrement the
configuration number.
7.After selecting the number required,
press the Cycle Selection key (Fig A-4) to
confirm.
8.Power the machine down.
9.Move the two microswitches (Fig B-3) to
the OFF position.
10.Power the machine up: the selected con-
figuration number appears on the dis-
play.
Visual temperature display: ºF - ºC
Depending on the model you select in the pre-
vious table, the temperature will be displayed in
ºF or ºC.
If you want to change from ºF to ºC and vice
versa you just need to select the model in the
table following the steps of the previous para-
graph.
OPERATION
S -
TART UP
1.Open the 3/4" stopcock to allow water to
enter the machine.
2.Turn on the switch. Turn on the booster
pump if one has been incorporated to the
machine.
3.Check that the filter of the motor-driven
pump (M), the upper filters (N) and the
drain plug are in place.
4.Turn the main switch (Fig. A-1) to the ON
position for the automatic filling of the
8
ENGLISH
wash tank and the connection of the hea-
M
ODELS
ter elements.
OCK
5.The light indicator (Fig.A, C) turns on
0 SL- 1200BP
when the
131ºF/149ºF (55/60ºC) has been rea-
1 SL- 1200BP
ched. If the washer has no automatic
detergent dispenser, introduce the deter-
0 SL- 1200BP
gent into the tank: 1/2 coffee cup at the
beginning of the first cycle and a same
1 SL- 1200BP
amount every 10 cycles approximately.
6.Automatic Start Cycle:
-Place the objects to be washed in a bas-
ket (rack).
-Press key A-6 to activate the automatic
cycle. The associated LED turns on.
-Select the washing programme by pres-
sing key A-4, according to the level of
soiling. The relevant red LED will turn
on.
-Close the door. The cycle will start auto-
matically and first the washing phase
indicator (A-g) will turn on, followed by
the rinsing indicator (A-h).
7.Non-automatic Start Cycle:
-Place the objects to be washed in a bas-
ket (rack).
-Press key A-6 with the LED off, to com-
mand the manual start cycle.
-Close the door.
-Select the washing programme by pres-
sing key A-4, according to the level of
soiling. The relevant red LED will turn
on.
-Press the Start Cycle key (A-5). The was-
hing phase indicator light (A-g) turns on.
The machine completes the entire was-
hing cycle. If you press the Start Cycle
key (A-5) again during the washing
phase, the programme immediately
shifts to the rinsing process. Pressing
the said key during the rinsing phase
causes the machine to stop.
8.When the complete cycle has finished,
the two indicators (A-g) and (A-h) flash.
9.Models with a drain pump: With the door
open, press key (A-7) to start the drain
pump for a given period of time, which is
long enough to empty the tank. At the
end of this time, the pump stops. Press
key (A-7) to alternately start and stop the
pump. With overflow (C-2) in place, any
residual water will be removed from the
tank.
10.Models "BP":
The Break-tank has two (2) level swit-
ches (high-low) and an overflow pipe dis-
charging into the wash tank. Once the
main switch has been turned on, filling
of boiler, Break-tank and wash tank is
done automatically. Due to the two level
detection switches, the pressure pump
operates alternately.
With a full tank,The drain pump works at
the same time as water enters the Break-
tank, so that water would flow into the was-
washing temperature hing tank through the break-tank overflow
pipe in the event of a level switch failure.
D
The dishwasher is prepared for its fitting
with an adjustable detergent dispenser, the
part number of which appears on the spare
parts list. This dispenser has to be installed
in the machine base, in holes provided for
this purpose, as shown on the exploded
view. At the rear of the wash tank, there is
an opening where to insert the detergent
injection nozzle.
The dispenser delivers about 0.7ml/s of
detergent (maximum). At the first filling of
the tank, feeding of detergent is roughly
119ml in 170s, resulting in a maximum con-
centration of 3ml/l. At each cycle, the dis-
penser delivers 10ml of detergent. It is pos-
sible to reduce the injected quantity by tur-
ning the adjusting screw on the dispenser.
R
Verify that the rinsing aid reservoir is full.
With the machine running, actuate the
main switch several times (5 or 6) during
the washing cycle and check whether the
tube fills up with rinsing aid and goes in
the boiler. Setting the dispenser is done by
turning an adjusting screw on the front
lower panel in the direction shown on the
panel graph.
In order to determine whether the amount
of rinsing aid is adequate, look at the glas-
ses against the light. If there are water dro-
plets on the glass, the amount of rinsing
aid is insufficient; if streaks develop, the
quantity of rinsing aid is too much.
I
The auxiliary tables are fastened with bolts
inserted into the threaded holes (D) either
in the bottom side of the machine or in the
bottom front (D)page 28. The top surface
of the tables is press-fit into the tank.
M
Models with no drain pump: Remove the
top filters from the tank and take out the
overflow pipe. Water will fall by gravity.
Models 'B' with a drain pump:
·Open the lid and take out the drain plug.
·Press the drain key (A-7) as specified on
ETERGENT DISPENSER
INSING AID DISPENSER
NSTALLATION OF AUXILIARY TABLES
D
ACHINE RAINING
the control panel, with the lid open. The
drain pump operates during the program-