Tabla de contenido
Idiomas disponibles
Idiomas disponibles
REMOVABLE INNER COMFORT PADDING
9.
Inner Comfort Padding Disassembly
To remove the inner comfort padding, lift the VPS and open the visor completely (see instructions above).
9.1.
Open the chin strap (see specific instructions).
9.2.
Hold the left front part of the liner and pull it upwards in order to remove the liner flap from the support fixed to the
polystyrene inner shell (Fig. 13). Then repeat the same steps for the central front and right flap.
9.3.
Remove the left and right sides of the comfort padding from the cavity between the inner polystyrene shell, the
outer shell and the VPS side guides (Fig. 14).
9.4.
Unhook the left rear flap of the liner from the support fixed to the polystyrene inner shell by slightly pulling the com-
fort padding towards the inside of the helmet (Fig. 15). Then repeat the same steps for the central and right flap.
9.5.
Remove the chin straps from the elastic loops on the straps and the from the liner side slots (Fig. 16A)..
9.6.
Completely remove the liner from the helmet.
10.
Inner Comfort Padding Assembly
10.1. Insert the liner correctly into the helmet and fit it well against the base
10.2. Pull the left rectangular textile extension of the liner (Fig. 16B) and insert the chin strap into the corresponding slot
in the lateral side of the liner (Fig. 16A) then fold the rectangular textile extension of the liner inside the padding.
Follow the same steps on the right side of the helmet.
10.3. Insert the right and left sides of the liner in the cavity between the inner polystyrene shell, the outer shell and the
VPS side guides (Fig. 14).
10.4. Insert the central rear flap of the liner into its seat on the support fixed to the polystyrene inner shell and push it
downwards until it is completely locked. Follow the same steps for the right and left rear flaps. (Fig. 15).
10.5. Insert the left front flap of the liner into its seat on the support fixed to the polystyrene inner shell and push it dow-
nwards until it is completely locked. Follow the same steps for the central and right flap (Fig. 13).
NOTE: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should
be smooth. If this is not the case, repeat the steps 9.2. and 10.5.
10.6. Insert the chin straps in the elastic loops on the straps and pull it towards the inside of the helmet.
WARNING
-
Remove the inner comfort padding only when cleaning or washing is require.
-
Never use the helmet if the all parts of inner comfort padding have not been correctly and completely reassembled
-
Before washing the inner comfort padding, make sure to remove all the removable sponge parts. Replace them
correctly after washing.
REMOVABLE INNER COMFORT PADDING
9.
Inner Comfort Padding Disassembly
To remove the inner comfort padding, lift the VPS and open the visor completely (see instructions above).
9.1.
Open the chin strap (see specific instructions).
9.2.
Hold the left front part of the liner and pull it upwards in order to remove the liner flap from the support fixed to the
polystyrene inner shell (Fig. 13). Then repeat the same steps for the central front and right flap.
9.3.
Remove the left and right sides of the comfort padding from the cavity between the inner polystyrene shell, the
outer shell and the VPS side guides (Fig. 14).
9.4.
Unhook the left rear flap of the liner from the support fixed to the polystyrene inner shell by slightly pulling the com-
fort padding towards the inside of the helmet (Fig. 15). Then repeat the same steps for the central and right flap.
9.5.
Remove the chin straps from the elastic loops on the straps and the from the liner side slots (Fig. 16A)..
9.6.
Completely remove the liner from the helmet.
10.
Inner Comfort Padding Assembly
10.1. Insert the liner correctly into the helmet and fit it well against the base
10.2. Pull the left rectangular textile extension of the liner (Fig. 16B) and insert the chin strap into the corresponding slot
in the lateral side of the liner (Fig. 16A) then fold the rectangular textile extension of the liner inside the padding.
Follow the same steps on the right side of the helmet.
10.3. Insert the right and left sides of the liner in the cavity between the inner polystyrene shell, the outer shell and the
VPS side guides (Fig. 14).
10.4. Insert the central rear flap of the liner into its seat on the support fixed to the polystyrene inner shell and push it
downwards until it is completely locked. Follow the same steps for the right and left rear flaps. (Fig. 15).
10.5. Insert the left front flap of the liner into its seat on the support fixed to the polystyrene inner shell and push it dow-
nwards until it is completely locked. Follow the same steps for the central and right flap (Fig. 13).
NOTE: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should
be smooth. If this is not the case, repeat the steps 9.2. and 10.5.
10.6. Insert the chin straps in the elastic loops on the straps and pull it towards the inside of the helmet.
WARNING
-
Remove the inner comfort padding only when cleaning or washing is require.
-
Never use the helmet if the all parts of inner comfort padding have not been correctly and completely reassembled
-
Before washing the inner comfort padding, make sure to remove all the removable sponge parts. Replace them
correctly after washing.
8
8
Tabla de contenido
