Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Do not use or leave the hood without the lamp correctly
mounted due to the possible risk of electric shocks.
We will not accept any responsibility for any faults, damage or
fires caused to the appliance as a result of the non-
observance of the instructions included in this manual.
Installation
The minimum distance between the supporting surface for the
cooking equipment on the hob and the lowest part of the
range hood must be not less than 50cm from electric cookers
and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a
greater distance, this must be adhered to.
Electrical connection
The mains power supply must correspond to the rating
indicated on the plate situated inside the hood. If provided with
a plug connect the hood to a socket in compliance with current
regulations and positioned in an accessible area, after
installation. If it not fitted with a plug (direct mains connection)
or if the plug is not located in an accessible area, after
installation, apply a double pole switch in accordance with
standards which assures the complete disconnection of the
mains under conditions relating to over-current category III, in
accordance with installation instructions.
Warning! Before re-connecting the hood circuit to the mains
supply and checking the efficient function, always check that
the mains cable is correctly assembled.
Mounting
Fig. 5-6-7
Before beginning installation:
•
Check that the product purchased is of a suitable size for
the chosen installation area.
•
Remove the charcoal (*) filter/s if supplied (see also
relative paragraph). This/these is/are to be mounted only
if you want lo use the hood in the filtering version.
•
Check (for transport reasons) that there is no other
supplied material inside the hood (e.g. packets with
screws (*), guarantees (*), etc.), eventually removing
them and keeping them.
•
If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to
rear wall/ceiling. Otherwise put a thick, protective
covering over countertop, cooktop or range to protect
from damage and debris. Select a flat surface for
assembling the unit. Cover that surface with a protective
covering and place all canopy hood parts and hardware
in it.
•
In addition check whether near the installation area of the
hood (in the area accessible also with the hood mounted)
an electric socket is available and it is possible to
connect a fumes discharge device to the outside (only
suction version).
•
Carry out all the masonry work necessary (e.g.
installation of an electric socket and/or a hole for the
passage of the discharge tube).
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take
the weight of the hood. Do not tile, grout or silicone this
appliance to the wall. Surface mounting only.
This hood is designed for fitting in a cabinet or on some other
support.
Preparing the wall unit (Fig.5)
First make sure the wall unit is suitable for the hood according
to the dimensions specified in the drawings.
Make the necessary holes for the insertion of the electric
cable and the exhaust pipe.
Make the same holes on the roof of the wall unit.
Fixing the brackets to the wall units (Fig.6-7)
Apply the template on the right internal side of the wall unit.
The lower and upper edges of the template must coincide with
the lower and upper edges of the wall unit (without
considering the possible door).
Mark the two fixing points.
Fix bracket R to the wall unit with 2 screws.
Note! For proper positioning screw the screws in the smallest
holes of the bracket.
Carry out the same operation on the left internal side of the
wall unit (Bracket L).
Before installing the hood (Fig.8)
In the case of wall units deeper than the hood it is possible to
install a spacer.
The spacer can cover depth differences not bigger than 5 cm
Measure the difference between the wall unit depth and the
hood depth and remove the excess by a cutter.
Fix the spacer on the back of the hood with 3 screws.
Remove the grease filter/s (Fig.9)
Installing the glass (Fig.10)
Open the pull-out drawer.
Remove the front panel, taking away the screws that fix it to
the hood.
Apply the glass to stop on the support tongues.
Reinstall and fix the front panel with the screws.
Installing the hood on the wall unit (Fig.11-15)
Insert the hood into the wall unit sliding the brackets of the
hood on the brackets fixed on the wall unit down to end stop.
Get the electric cable through the special slots obtained on the
wall unit.
Block the hood fixing the brackets to each other with 2 screws
(one each side).
Pre-install the exhaust pipe connecting flange of suitable
length and diameter for the fume exhaust to the outside
(Exhaust version Fig.13) or on the roof of the wall unit (Filter
version Fig.14).
Fix the connecting flange to the hood exhaust hole (pressure
fixing).
For proper fixing, make sure that the index printed on the
flange coincides with the special guide obtained on the
exhaust hole.
24
Capítulos
Tabla de contenido
