Tabla de contenido
Idiomas disponibles
Idiomas disponibles
9.3
Place the PINLOCK
®
WARNING: The silicone-sealed profile of the PINLOCK
9.4
Insert one side of the PINLOCK
9.5
Widen the visor and fasten the other side of the PINLOCK
9.6
Release the visor.
9.7
Remove the protective film from the PINLOCK
adheres to the visor.
9.8
Fit the visor on the helmet (see instructions above).
Checking and Adjusting the PINLOCK
Check the correct PINLOCK
If the PINLOCK
®
inner visor is not tightly fixed to the visor, move both external adjustment levers upwards to increase the stretch
(Fig. 14). This operation must be carried out gradually. The maximum stretch is achieved when the pin adjustment external levers
are turned outwards.
WARNING
-
The presence of dust between the two visors may produce scratches on both surfaces.
-
Scratched PINLOCK
-
Regularly check the correct stretch of the PINLOCK
-
If the helmet visor fogs up and/or condensation forms between the visors, check that the PINLOCK
tly assembled and stretched.
-
An excessive and early stretch of the PINLOCK
permanent deformations with subsequent inability to correctly perform any following adjustments.
-
Intense sweating /breathing, the use under particular weather conditions (low temperatures, and/or high humidity and/or sud-
den changes in temperature and/or heavy rain) and/or intense and prolonged use may affect the performance of the PINLOCK
inner visor and cause fogging or formation of condensation. In such cases, after using the helmet and to restore the system
efficiency, remove the PINLOCK
must be applied to the helmet, in order to dry out humidity in case it has formed up as a consequence of the conditions descri-
bed above.
10
Inner Visor PINLOCK
10.1 Remove the visor equipped with the Pinlock
10.2 Widen the visor and release the Pinlock
10.3 Release the visor.
9.3
Place the PINLOCK
®
WARNING: The silicone-sealed profile of the PINLOCK
9.4
Insert one side of the PINLOCK
9.5
Widen the visor and fasten the other side of the PINLOCK
9.6
Release the visor.
9.7
Remove the protective film from the PINLOCK
adheres to the visor.
9.8
Fit the visor on the helmet (see instructions above).
Checking and Adjusting the PINLOCK
Check the correct PINLOCK
If the PINLOCK
®
inner visor is not tightly fixed to the visor, move both external adjustment levers upwards to increase the stretch
(Fig. 14). This operation must be carried out gradually. The maximum stretch is achieved when the pin adjustment external levers
are turned outwards.
WARNING
-
The presence of dust between the two visors may produce scratches on both surfaces.
-
Scratched PINLOCK
-
Regularly check the correct stretch of the PINLOCK
-
If the helmet visor fogs up and/or condensation forms between the visors, check that the PINLOCK
tly assembled and stretched.
-
An excessive and early stretch of the PINLOCK
permanent deformations with subsequent inability to correctly perform any following adjustments.
-
Intense sweating /breathing, the use under particular weather conditions (low temperatures, and/or high humidity and/or sud-
den changes in temperature and/or heavy rain) and/or intense and prolonged use may affect the performance of the PINLOCK
inner visor and cause fogging or formation of condensation. In such cases, after using the helmet and to restore the system
efficiency, remove the PINLOCK
must be applied to the helmet, in order to dry out humidity in case it has formed up as a consequence of the conditions descri-
bed above.
10
Inner Visor PINLOCK
10.1 Remove the visor equipped with the Pinlock
10.2 Widen the visor and release the Pinlock
10.3 Release the visor.
inner visor on the visor.
®
inner visor on one of the visor pins and hold it in position (Fig. 13).
®
®
Inner Visor Stretch
®
inner visor assembly by opening and closing the visor and making sure that they do not move.
®
visors and inner visors may cause reduced visibility and must therefore be replaced.
®
®
inner visor from the helmet visor and let it dry with dry and warm air. The same procedure
®
Disassembly
®
inner visor (see instructions above).
®
inner visor from the pins (Fig. 14).
inner visor on the visor.
®
inner visor on one of the visor pins and hold it in position (Fig. 13).
®
®
Inner Visor Stretch
®
inner visor assembly by opening and closing the visor and making sure that they do not move.
®
visors and inner visors may cause reduced visibility and must therefore be replaced.
®
®
inner visor from the helmet visor and let it dry with dry and warm air. The same procedure
®
Disassembly
®
inner visor (see instructions above).
®
inner visor from the pins (Fig. 14).
®
inner visor must be in contact with the inner surface of the visor.
®
inner visor to the second pin (Fig. 14).
inner visor and check that the entire silicone-sealed profile of the inner visor
®
inner visor to prevent the it from moving and scratching both surfaces.
inner visor may result in excessive adherence against the visor surface and/or
8
®
inner visor must be in contact with the inner surface of the visor.
®
inner visor to the second pin (Fig. 14).
inner visor and check that the entire silicone-sealed profile of the inner visor
®
inner visor to prevent the it from moving and scratching both surfaces.
inner visor may result in excessive adherence against the visor surface and/or
8
®
inner visor is both correc-
®
®
inner visor is both correc-
®
Tabla de contenido
