Tabla de contenido
Idiomas disponibles
Idiomas disponibles
REMOVABLE PROTECTIVE CHIN GUARD
7
Removable Protective Chin Guard Release
7.1
Open the visor completely..
7.2
Pull the right and left chin guard release levers downwards and at the same time remove the chin guard from the helmet by
pulling it outwards (Fig. 10).
WARNING
Every time you wish to release the chin guard to use your helmet in the jet configuration, insert the right and left chin guard locking
slot covers (chin guard covers) in the slots on the right and left side frames and push them towards the inside of the helmet until you
hear a fastening click (Fig. 11).
NOTE: The left and right chin guard covers are different from each other and are marked on their back as "DX" (right) and "SX" (left).
8
Removable Protective Chin Guard Fastening
Before fastening the chin guard to the helmet, remove the chin guard covers by performing the following operations:
8.1
Open the visor completely.
8.2
Remove the right and left chin guard covers by pulling them outwards (Fig. 11).
8.3
Insert the right and left chin guard ends simultaneously into the slots on the corresponding side frames of the helmet and press
the chin guard towards the inside of the helmet until you hear the fastening click on both sides (Fig. 12).
8.4
Make sure the chin guard is correctly fastened at both ends by gently pulling it towards the outside of the helmet.
WARNING
-
Never remove or disassemble the semi-rigid inner padding of the protective chin guard.
-
When the helmet is used without the removable protective chin guard, always assemble the chin guard covers supplied.
-
If in doubt on how the manual chin guard release device works, please contact a Nolan dealer.
(Available as standard or accessory/spare part).
9
Inner Visor PINLOCK
9.1
Disassemble the visor (see instructions above).
9.2
Make sure that the inner surface of the visor is clean and check that the pin adjustment external levers are turned inwards
(Fig. 15).
REMOVABLE PROTECTIVE CHIN GUARD
7
Removable Protective Chin Guard Release
7.1
Open the visor completely..
7.2
Pull the right and left chin guard release levers downwards and at the same time remove the chin guard from the helmet by
pulling it outwards (Fig. 10).
WARNING
Every time you wish to release the chin guard to use your helmet in the jet configuration, insert the right and left chin guard locking
slot covers (chin guard covers) in the slots on the right and left side frames and push them towards the inside of the helmet until you
hear a fastening click (Fig. 11).
NOTE: The left and right chin guard covers are different from each other and are marked on their back as "DX" (right) and "SX" (left).
8
Removable Protective Chin Guard Fastening
Before fastening the chin guard to the helmet, remove the chin guard covers by performing the following operations:
8.1
Open the visor completely.
8.2
Remove the right and left chin guard covers by pulling them outwards (Fig. 11).
8.3
Insert the right and left chin guard ends simultaneously into the slots on the corresponding side frames of the helmet and press
the chin guard towards the inside of the helmet until you hear the fastening click on both sides (Fig. 12).
8.4
Make sure the chin guard is correctly fastened at both ends by gently pulling it towards the outside of the helmet.
WARNING
-
Never remove or disassemble the semi-rigid inner padding of the protective chin guard.
-
When the helmet is used without the removable protective chin guard, always assemble the chin guard covers supplied.
-
If in doubt on how the manual chin guard release device works, please contact a Nolan dealer.
(Available as standard or accessory/spare part).
9
Inner Visor PINLOCK
9.1
Disassemble the visor (see instructions above).
9.2
Make sure that the inner surface of the visor is clean and check that the pin adjustment external levers are turned inwards
(Fig. 15).
®
Assembly
®
Assembly
7
7
Tabla de contenido
