Tabla de contenido
Kit Due Fili
OPERATION
Carry out connections as described in this leaflet. When entrance panel
push-button is pressed, a call signal is heard on monitor (and faintly also
in the speech unit). The monitor comes on immediately showing a clear
image of the caller. Lift the handset to communicate with the caller. If , on
calling, the handset is already unkooked, the audio connection is immedi-
ately established.
If required operate the electric lock by pressing proper push-button
. The monitor turns off after nearly 30'' (adjustable on the panel from 30 to
90 seconds). The installation can be switched on by pressing the push-but-
ton with the symbol
, thus allowing an external view when required.
When two cameras are installed, both cameras are cyclically activated on
pressing the push-button.
Type 6328/CD is designed for use with hearing aids used by hearing
impaired people. To activate it, select the "T" position on the hearing aid.
TECHNICAL CHARACTERISTICS OF MONITOR TYPE 6328, 6328/C
OR 6328/CD
- Surface wall-mounted monitor in ABS; standard colour: white.
- Back plate and expansion plugs or 3 module back box for surface
wall-mounting.
- Screen:
- B/N monitor 3,5" screen (6328)
- Colour monitor TFT LCD 3,5" (for 6328/C, 6328/CD)
- Electronic circuit on interchangeable cards
- Video signal:
- Standard CCIR, 625 lines, 50 images (6328)
- Standard PAL type G, 625 lines, 50 images (6328/C, 6328/CD)
- 4MHz video pass band
- Operating temperature: 0° to +40° C
- Electronic chime
- Input for outdoor call with ton different from the entrance panel call.
- Output for additional chime Art. 860A
- Supply voltage from the bus.
- Input for additional power supply (type 6923), if the installation is config-
urated for the simultaneous switching on of two monitors.
- Configuration (through jumpers) to disable the chime from one o more
entrance panel push-buttons.
- Configuration (through jumpers) to block the lock activation when the
monitor is switched off.
- External dimensions: 204x220x71
CONTROLS (Fig. 3)
- Chime volume adjustment by means of cursor "A"
- Brightness control: through knob "B"
- Contrast control: through knob "C"
- Push-button for electric lock release
- Autoswitching push-button
- Push-button
for 1st auxiliary service (allows activation of relais type
682R).
- Pressing push-buttons
ry service and relay type 682R are activated.
- LED for exlusion of chime "D". It lights up with a steady light when the
chime has been excluded by using the "A" cursor and it flashes when
there is a conversation in progress on the installation ("engaged" signal-
ling).
- LED for open door "E". When using only an entrance panel the LED
remains lit steadily when the door is open. When two doors are installed,
it remains lit steadily when both door locks are open. On the contrary if
only one of the doors is open, the LED flashes once for the first door,
twice for the second door.
TERMINALS OF MONITOR TYPE 6328, 6328/C, OR 6328/CD
1,2)
BUS Line
3,4)
For connection of additional chime type 860A (see variation 1)
12, 13) Additional power supply art. 6923 (terminal 12 = positive)
V3, M) connection for outdoor call push-button.
EN
5
4
3
2
1
and
at the same time, the 2nd auxilia-
ID1 ID0 MONITOR
n°1
n°2
n°3
n°4
PROGRAMMING OF MONITOR TYPE 6328, 6328/C OR 6328/CD
5
4
3
2
1
Monitor identification code
ID1 ID0 MONITOR
n°1
n°2
n°3
n°4
ID1 ID0 MONITOR
Lock release
Removing contact 3 from the monitor it is possible to open the door lock
always, with monitor switched off or switched on. Inserting the jumper, it is
possible to release the door lock from the monitor only after the call.
Association of call push-button from the entrance panel
To associate the entrance panel push-button with which to call and
switch on the monitor, operate on contacts 4 and 5: contact 4 for the right
hand panel push-button or 1° push-button and contact 5 for the left hand
push-button or 2° push-button. Inserting the jumpers the call is excluded,
removing them the call and the monitor activation is enabled.
1 2 3 4 5
ID 0
ID 1
4 5
The operation of monitor type
6328 is managed by the 5 contact
setting on the back of monitor.
To activate the functions insert
or remove the jumpers supplied
with monitor.
Programming must be carried out
before powering the installation.
5
4
3
2
1
When on the intallation there is
1 2 3 4 5
more than one monitor it is nec-
essary to identify the monitor with
a different code. The identifica-
tion code is assigned by inserting
the jumpers in contacts 1 and
ID 0
2 (ID0 and ID1) as indicated in
the figure.
ID 1
1 2 3 4 5
ID 0
n°1
ID 1
n°2
n°3
n°4
CH2
CH1
APERTURA SERRATURA SEMPRE
LOCK RELEASE ALWAYS
CH2
APERTURA SERRATURA DOPO CHIAMATA
LOCK RELEASE AFTER CALL
CH1
CH2
CH1
APERTURA SER
LOCK RELEAS
CH2
CH1
APERTURA SER
LOCK RELEAS
APERTU
LOCK R
APERTUR
LOCK RE
7
Tabla de contenido
