Makita LS1216 Manual De Instrucciones página 18

Stopper arm (Fig. 11)
The lower limit position of the blade can be easily
adjusted with the stopper arm. To adjust it, rotate the
stopper arm in the direction of the arrow as shown in the
figure. Adjust the adjusting screw so that the blade stops
at the desired position when lowering the handle fully.
Adjusting the miter angle (Fig. 12)
Push the grip so that the cams engages and turn it clock-
wise until it stops. Turn the turn base while pressing
down the lock lever. When you have moved the grip to
the position where the pointer points to the desired angle
on the miter scale, turn the grip to 90° counterclockwise
to lock the turn base.
CAUTION:
• When turning the turn base, be sure to raise the handle
fully.
• After changing the miter angle, always secure the turn
base by turning the grip to 90° counterclockwise.
Adjusting the bevel angle (Fig. 13, 14 & 15)
To adjust the bevel angle, loosen the lever at the rear of
the tool counterclockwise. Push the latch lever forward as
shown in the figure fully while supporting the weight of
the saw head so as to release the pressure on the lock
pin.
When tilting the carriage to the right, tilt the carriage to
the left slightly after loosening the lever and press the
releasing button. With the releasing button being
pressed, tilt the carriage to the right.
Tilt the saw blade until the pointer points to the desired
angle on the bevel scale. Then tighten the lever clock-
wise firmly to secure the arm.
When the latch lever is pulled toward yourself, the saw
blade can be locked using positive stops at the right and
left 22.5° and 33.9° angle to the base surface.
When the latch lever is pushed forward as shown in the
figure, the saw blade can be locked at an desired angle
within the specified bevel angle range.
CAUTION:
• When tilting the saw blade, be sure to raise the handle
fully.
• After changing the bevel angle, always secure the arm
by tightening the lever clockwise.
• When changing bevel angles, be sure to position the
kerf boards appropriately as explained in the "Position-
ing kerf board" section.
Slide lock adjustment (Fig. 16)
To lock the lower slide pole, pull the lock lever toward
yourself.
To lock the upper slide pole, turn the locking screw clock-
wise.
Switch action
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
• Do not pull the switch trigger hard without pressing in
the lock-off button. This can cause switch breakage.
For European countries (Fig. 17)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push the lever to the left, press in the lock-off button and
then pull the switch trigger. Release the switch trigger to
stop.
18
A hole is provided in the switch trigger for insertion of
padlock to lock the tool off.
For all countries other than European countries
(Fig. 18)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
A hole is provided in the switch trigger for insertion of
padlock to lock the tool off.
WARNING:
• Do not use a lock with a shank or cable any smaller
than 6.35 mm in diameter.
• NEVER use tool without a fully operative switch trigger.
Any tool with an inoperative switch is HIGHLY DAN-
GEROUS and must be repaired before further usage.
• For your safety, this tool is equipped with a lock-off but-
ton which prevents the tool from unintended starting.
NEVER use the tool if it runs when you simply pull the
switch trigger without pressing the lock-off button.
Return tool to a Makita service center for proper repairs
BEFORE further usage.
• NEVER tape down or defeat purpose and function of
lock-off button.
Electronic function
Constant speed control
• Possible to get fine finish, because the rotating speed
is kept constantly even under the loaded condition.
Soft start feature
• Soft start because of suppressed starting shock.
Laser beam action
For model LS1216L only
CAUTION:
• LASER RADIATION
Do not stare into beam.
To turn on the laser beam, press the upper position (I) of
the switch. Press the lower position (O) to turn off.
(Fig. 19)
Laser line can be shifted to either the left or right side of
the saw blade by adjusting the adjusting screw as fol-
lows. (Fig. 20)
1. Loosen the adjusting screw by turning it counter-
clockwise.
2. With the adjusting screw loosened, slide the adjust-
ing screw to the right or left as far as it goes.
3. Tighten the adjusting screw firmly at the position
where it stops sliding.
Laser line is factory adjusted so that it is positioned within
1 mm from the side surface of the blade (cutting posi-
tion).
NOTE:
• When laser line is dim and almost or entirely invisible
because of the direct sunlight in the indoor or outdoor
window-by work, relocate the work area to a place not
exposed to the direct sunlight.