GB
CAMERA Type 68TU/K, 68TC/K
Colour cameras (type 68TC/K) and B/W cameras (type 68TU/K) for use with
1300 series panel (type 13K1) for 2-wire videokit installations.
Camera technical features (Type 68TU/K)
-
CCD 1/3" color sensor B/W
-
3,7mm F4.0 auto-iris lens with non-adjustable focus
-
Automatic brightness control
-
Manual traversing on the vertical and horizontal axis
-
Standard video signal CCIR 625 lines, 50 images (EIA on request)
-
Operating temperature from - 5° to + 45° C.
-
Subject lighting by means of infrared LEDs
-
Name-tag lighting through LEDs
-
Built-in speech unit
-
Removable terminal block
-
Monitor call push-button.
-
Output for control of lighting floodlight by relay type 170/101
-
Local door release control from entrance panel.
-
Adjustable lock activation time (from 0 to 30 seconds).
-
Supply voltage from the bus.
-
External dimensions: 80x120x25 mm.
Camera technical features (Art. 68TC/K)
- Sensore CCD 1/3" a colori
- Obiettivo autoiride fuoco fisso 3,7mm F4,0
-
Standard video signal PAL type G, 625 lines, 50 images
-
Manual traversing on the vertical and horizontal axis
-
Vertical resolution: 330 TV lines or Greater
-
Effective picture: 512(H)x582(V) PAL
-
Electronic iris (shutter)
-
Video output voltage 1Vpp on 75 Ohms
-
Operating temperature -5° +45°C
-
Minimum lighting level 0,1 lux
-
Subject lighting by means of white light LEDs
- Name-tag lighting through LEDs
-
Built-in speech unit
-
Removable terminal block
-
Monitor call push-button.
-
Output for control of lighting floodlight by relay type 170/101
-
Local door release control from entrance panel.
-
Adjustable lock activation time (from 0 to 30 seconds).
-
Supply voltage from the bus.
-
External dimensions: 80x120x25 mm.
Camera adjustments (Art. 68TU/K, 68TC/K)
On the camera rear side find the following adjustments:
External
Internal
Lock activation
volume
volume
Camera terminals type 68TU/K, 68TC/K
CL, M)
Connection for relay type 170/101 for additional floodlight.
(for switching on illumination in the camera's observation zone)
It is activated for the time the camera is on.
CA, M)
Connection for additional lock push-button.
PA, M)
Connection for "open door" sensor. The sensor must be a nor-
mally open contact which closes when the door is open.
B1, B2)
BUS line
S-, S+)
Output for electric lock supply voltage (12V
V)
(Not used)
*
The panel supplies a current peak IT> 1A for 10 mS, followed by a hold
current I
= 200mA for the entire duration of the lock control.
M
Art. 68TC/K, 68TU/K
Camera activation
time
time
*
).
ENTRANCE PANEL/CAMERA identification code
If more cameras/entrance panels are installed on the building it is necessary
to identify the cameras with a different code. The identification code is assi-
gned by inserting the jumpers in the contacts as shown on the figure.
12V
LED CH2
Name tag lighting
LED
OPERATING DWELL TIME
The monitor, camera, door lock and auxiliary services mut operate accor-
ding to the following intermittent cycles.
Monitor and camera activation cycle:
max. 90 seconds activated, 90 seconds deactivated
Door lock cycle:
max. 1 second activated, 5 seconds deactivated
Auxiliary service cycle:
max. 90 seconds activated, 90 seconds deactivated
6/32
1st
IT=0
(Default)
2nd
IT=1
Name tag lighting
LED
2nd push-button
1st push-button
Microphone
Fig.12
camera
camera
Fig.13