Tabla de contenido
Idiomas disponibles
Idiomas disponibles
TRANSAXLE
GEAR SHIFT LEVER
NEU-
TRAL ADJUSTMENT
The transaxle
should be in neutral when the
gear shift lever is in neutral (N) (lock gate)
position.
The
adjustment
mspreset
at the
factory;
however,
if adjustment
is needed,
proceed
as follows:
1. Make sure transaxle
is in neutral (N).
NOTE:
When the tractor rear wheels move
freely, the transaxle
is in neutral.
2. Loosen
adjustment
bolt in front of the
right rear wheel.
3. Position the gear shift lever in the neutral
(N) position.
4. Tighten
adjustment
bolt securely.
NOTE:
If additional
clearance
is needed to
get to adjustment
bolt, move mower deck
height to the lowest position.
Gearshift
Adjustment Belt
Lever
..
_./_..._
TO REMOVE
WHEEL
FOR REPAIRS
1. Block up axle securely.
2.
Remove
axle cover, retaining
ring and
washers
to allow wheel
removal
(rear
wheels have a square key - Do not lose).
3. Repair ttre and reassemble.
NOTE: On rearwhee(s
on[y: align grooves in
rear wheel hub and axle. Insert square key.
4. Repiacewashers
and snap retaining ring
securely
in axle groove.
5.
Reptace axle cover.
NOTE: To sea[ tire punctures
and prevent
flat tires due to slow leaks, purchase
and
use tire sealant fro m Sears. Tire sealant also
prevents
tire dry rot and corrosion.
Washers
Reta,ning
A
__,
Cover.
X
I _ Ira'[
(( _
lm,1_
Sqy are___=_J
(Re_
28
TO CHECK BRAKE
If tractor requires
more than five (5) feet to
stop at highest speed in highest
gear on a
level, dry concrete
or paved surface, then
brake must be serviced,
You may also check brake by;
1. Parktractoron alevel, dryconcreteorpaved
surface,
depress
clutch/brake
pedal all
the way down an d engage parkin g brake.
2, Place gearshift
lever in neutral position.
The rear wheels must lock and skid when
you try to manually push the tractor forward.
If the rear wheels
rotate, then the brake
needs to be serviced.
Contact
a Sears
or
other qualified service
center.
TO START
ENGINE WITH A WEAK
BAT-
TERY
_I_WARNING:
Lead-acid
batteries
gener-
ate explosive
gases.
Keep sparks,
flame
and smoking materials away from batteries.
Always
wear eye protection
when around
batteries.
Ifyour batteryis too weakto start the engine, it
should be recharged.
(See "BATTERY" in the
MAINTENANCE
section of this manual).
If "jumper cables" are used for emergency
starting, follow this procedure:
IMPORTANT:
Your tractor is equipped with
a 12 volt system. The other vehicle must also
be a 12 volt system.
Do not use your tractor
battery to start other vehicles.
TO ATTACH JUMPER
CABLES
1. Connectoneend
ofthe RED cabletothe
POSITIVE
(+) terminal of each battery(A-
B), taking care netto short againsttracter
chassis.
2. Connect
one end of the BLACK
cable
to the NEGATIVE
(-) terminal (C) of fully
charged
battery.
3. Connect
the other end of the BLACK
cable (D) to good chassis ground,
away
from fuel tank and battery.
TO
REMOVE
CABLES,
REVERSE
ORDER
1. BLACK cable firstfrom
chassis and then
from the fully charged
battery.
2. RED cable last from both batteries.
Weak or Dead
Fully Charged
Battery
Battery
Tabla de contenido
