• Position the lawnmower on a straight, level surface.
• Remove the ignition key (10)
• Unscrew buttons 12 and 2
• Remove the tilt protection (fig. 16)
• Fold up the body (fig. 2)
• Remove the oil dipstick (21) by turning it to the left
• Use the included injector needle (g) and hose to
extract motor oil through the filling nozzle.
• Fill with fresh motor oil and check the oil level
Dispose of the used oil in accordance with applicable
regulations.
Air filter maintenance (Fig. 35 + 36)
Fouled air filters (20) diminish the motor performance
due to reduced air supply to the carburettor. Regular
inspection is therefore essential.
The air filter should be checked every 25 operating
hours and cleaned as required. The air filter must be
checked more often in case of very dusty air.
• Fold the body up as described while checking the
oil.
• Fold out the ejector chute. (Fig. 35)
• Take off the air filter cover (fig. 36) and remove the
air filter (A and B).
• Wash off the sponge filter (B) with water and dry it
completely.
• Clean the paper filter (A) with compressed air only
or by knocking them out.
Important: Never clean the air filter with petrol or
inflammable cleaning agents. Clean the paper filter
with compressed air or simply by knocking out any
soiling.
Maintenance of the spark plug (Fig. 33)
Check the spark plug for dirt and grime after 10 hours
of operation and if necessary clean it with a copper
wire brush. Thereafter service the spark plug after
every 50 hours of operation.
Pull off the spark plug boot with a twist. Remove the
spark plug (23) with a spark plug wrench.
Using a feeler gauge, set the gap to 0.75 mm( 0.030").
Refit the spark plug (23)taking care not to overtighten.
Replace fuse (Fig. 34)
• The electrical start is protected with a 10 A fuse.
• Never use another fuse or bypass the fuse.
Charge the battery (Fig. 29)
The battery is charged during operation. In any case,
frequent starting may make it necessary to charge
the battery with the included charging device (f):
• Plug the connector into the charging socket (7) and
the charging device (f) into a plug socket. 230 V
50 Hz
50 | GB
www.scheppach.com /
[email protected] / +(49)-08223-4002-99 / +(49)-08223-4002-58
• Charge the battery for min. 5 hours.
Charge the battery with a car charging device
(Fig. 30 + 31)
• You may also charge the battery with the included
charging cable (m) on an industry-standard car
charging device for 12 V lead batteries.
• Unplug the battery in this case (fig. 15).
• Connect the included charging cable (m) to the bat-
tery and connect the black cable with the - pole and
the red cable with the + pole of the charging device
(fig. 30 + 31).
Attention! Never exchange the + and - poles.
Always store the lawnmower with a fully loaded bat-
tery.
Tyre pressure:
Check the tyre pressure prior to starting!
The correct tyre pressure is 1.8 bar in the front wheels
and 1.3 bar in the rear wheels.
Important: If the tyre pressure is too low, the risk of
damage to the valves and therefore the hoses in-
creases.
Repairs
After any repair or maintenance work, check that all
safety-related parts are in place and in proper work-
ing order. All parts which may cause injury must be
kept where they are inaccessible to children or oth-
ers.
Important: In accordance with product liability legis-
lation we are not liable for any damages caused by
improper repairs or the use of spare parts that are not
original spare parts or parts approved by us.
In addition, we are also not liable for any damages
arising from improper repairs. Such work should be
performed by a customer services workshop or au-
thorized specialist. The same applies to accessory
parts.
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering re-
placement parts:
• Type of machine
• Article number of the machine
Spare parts/accessories
Lawn mower blade - Article no.: 7911200616