Charging The Battery (See Figure B); Inserting/Changing The Saw Blade; Dust/Chip Extraction - Bosch NanoBlade EasyCut 12 Manual Original

14 | English
Charging the battery (see figure B)
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
To remove the battery (5), press the release button (6) and
pull the battery back and out of the power tool. Do not use
force to do this.
Battery charge-control indicator
When the on/off switch (4) is pressed in halfway or com-
pletely, the battery charge indicator (8) indicates the bat-
tery's state of charge for a few seconds. It consists of an LED
which lights up in two colours.
Selecting the saw blade
Only use saw blades that are suitable for the material you are going to cut. The saw blade should not be longer than required
for the cut you want to make.
Saw blade
NanoBlade Wood Basic
NanoBlade Wood Speed
NanoBlade Wood Speed
Inserting the saw blade (see figure A)
Use only clean saw blades. Make sure that the saw
u
blade receptacle is free of chips and sawdust.
Use the locking lever (10) to open the cover (9) of the saw
blade receptacle. Insert the saw blade as shown in the fig-
ure. Make sure that the drive shaft and the end of the saw
blade fit in the recess on the saw blade receptacle (12).
Close the cover of the saw blade receptacle and lock it with
the locking lever. You should hear the locking lever click into
place.
The chain of the saw blade is tensioned automatically.
If the chain slips through or becomes detached from the
guide unit, open and close the cover (9) of the saw blade re-
ceptacle.
Removing the saw blade
Open the locking lever (10) and lift the cover (9) of the saw
blade receptacle all the way up. Remove the saw blade.
1 609 92A 4L4 | (12.03.2019)
LED
Lit green
Lit red
Flashing red
A) The battery charge indicator will also flash red if the battery has
overheated or overloaded.

Inserting/changing the saw blade

When fitting or changing the saw blade, wear protect-
u
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
Take care not to hold the power tool close to the on/
u
off switch or by the on/off switch and lock-off button
when changing the saw blade. There is risk of injury
from unintentionally pressing the on/off switch.
Avoid contact with the skin when changing a saw
u
blade and use protective gloves in perfect condition.
The saw blade can become hot when in operation for a
long time.
Do not pull on the chain and do not pull the chain off
u
the guide unit.
Always replace a complete saw blade with another complete
saw blade. The chain cannot be replaced on its own.
Cutting depth Order number
50 mm 2 609 256 D83
50 mm 2 609 256 D84
65 mm 2 609 256 D86

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Never bend the saw blade
u
Capacity
≥ 30%
<30%
A)
0%
Materials
Wood, plastic (PVC, PC, PMMA)
Wood, plastic (PVC, PC, PMMA)
Wood, plastic (PVC, PC, PMMA)
Bosch Power Tools