Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Special information about the laser
Caution! Laser radiation
Do not look into the beam
Laser class 2
¡Atención! Radiación Láser!
¡No mirar directamente al trayecto del rayo!
Especificación Láser: Clase Laser 2
Laser Klasse 2
: 650 nm; P
•
Never look directly into the laser path.
•
Never direct the laser beam at reflecting
surfaces or persons or animals. Even a low
output laser beam can inflict injury on the eye.
•
Caution: It is vital to follow the work proce-
dures described in these instructions. Using
the equipment in any other way may result in
hazardous exposure to laser radiation.
•
Never open the laser module.
•
It is prohibited to carry out any modifications
to the laser to increase its power.
•
The manufacturer cannot accept any liability
for damage due to non-observance of the
Anl_SA_TE_MS_18_20_Li_Solo_SPK8.indb 28
Anl_SA_TE_MS_18_20_Li_Solo_SPK8.indb 28
GB
0
- 28 -
safety information.
•
Switch off the laser when not in use.
General safety instructions for electric tools
WARNING Read all the safety information,
instructions, illustrations and technical data
provided on or with this power tool. Failure
to adhere to the following instructions may
result in electric shock, fi re and/or serious
injury.
Keep all the safety information and instruc-
tions in a safe place for future use.
The term „power tool" used in the safety informati-
on and instructions refers to power tools operated
from the mains power supply (with a power cable)
and to battery operated power tools (without a
power cable).
1. Workplace safety
a) Keep your work area clean and well illu-
minated. Untidy or unlit work areas can result
in accidents.
b) Do not operate the electric tool in an en-
vironment where there is a risk of explo-
sions and where there are infl ammable
liquids, gases or dust. Electric tools produ-
ce sparks which could set the dust or vapours
alight.
c) Keep the electric tool out of the reach of
children and other persons. If there is a
distraction, you may lose control of the appli-
ance.
2. Electrical safety
a) The connector plug from this electric tool
must fi t into the socket. The plug should
never be altered in any way. Never use adap-
ter plugs together with earthed electric tools.
Unaltered plugs and correct sockets reduce
the risk of an electric shock.
b) Avoid bodily contact with earthed sur-
faces such as pipes, heating, ovens and
fridges. The risk of electric shock is increa-
sed if your body is earthed.
c) Keep the tool out of the rain and away
from moisture. The ingress of water into an
electric tool increases the risk of an electric
shock.
d) Do not use the cable to carry the electric
tool, to hang it up or to pull it out of the
socket. Keep the cable away from heat, oil,
sharp edges and moving parts of the appli-
15.03.2018 14:19:54
15.03.2018 14:19:54
Capítulos
Tabla de contenido
