BFT LEO B CBB DL2 3 230 L02 Instrucciones De Instalación página 30

Logic
Definition
Configuration of
EXPO2 output
on input-output
EXPO1
expansion board
Configuration of
EXPO2 output
on input-output
EXPO2
expansion board
Traffic light
TRAFFIC LIGHT
pre-flashing
PREFLASHING
TRAFFIC LIGHT
Steadily lit red
RED LAMP
light
ALWAYS ON
CH logic= 0 - Control configured as Start E. Operation according to STEP-BY-STEP MOV. logic. External start for traffic light control.
CH logic= 1 - Control configured as Start I. Operation according to STEP-BY-STEP MOV. logic. Internal start for traffic light control.
CH logic= 2 - Control configured as Open.
The command causes the leaves to open.
CH logic= 3 - Control configured as Closed.
The command causes the leaves to close.
CH logic= 4 - Control configured as Ped.
The command causes the leaf to open to the pedestrian (partial) opening position. Operation according to STEP-BY-STEP. logic
Logica CH= 5- Control configured as STOP.
The command performs a STOP
CH logic= 6 - Control configured as AUX0. (**)
The control activates the AUX0 output
CH logic= 7 - Not used
CH logic= 8 - Not used
CH logic= 9 - Control configured as AUX3. (**)
The control activates the AUX3 output
CH logic= 10 - Control configured as EXPO1. (**)
The control activates the EXPO1 output
CH logic= 11 - Control configured as EXPO2. (**)
The control activates the EXPO2 output
(**) Active only if the output is configured as Monostable Radio Channel, Courtesy Light, Zone Light, Stair Light, Bistable Radio Channel or Timed Radio Channel.
TABLE "C" – RADIO MENU (RADIO)
Logic Description
Add 1ch Key
add 1ch
associates the desired key with the 1nd radio channel command.
Add 2ch Key
add 2ch
associates the desired key with the 2nd radio channel command.
Add 3ch Key
add 3ch
associates the desired key with the 3nd radio channel command.
Add 4ch Key
add 4ch
associates the desired key with the 4nd radio channel command.
Erase List
erase 64 WARNING! Erases all memorized transmitters from the receiver's memory.
Eliminates individual radio control
erase 1
Removes a radio control (if clone or replay is disabled) To select the radio control to be deleted, enter the position or press a button on the radio control to be deleted (the position is displayed)
Read receiver code
Displays receiver code required for cloning transmitters.
30 - LEO B CBB DL2 3 230 L02-LEO B CBB DL2 3 120 F02-LEO B CBB DL2 3 120 F02 PHOT USA16 - LEO B CBB DL2 3 230 SV
INSTALLATION MANUAL
Cross out
Default setting
11
4-5
11
6-7
0
0
Radio channel control configuration
used
0 Output configured as monostable Radio Channel.
1 Output configured as SCA (gate open light).
2 Output configured as Courtesy Light command.
3 Output configured as Zone Light command.
4 Output configured as Stair Light.
5 Output configured as Alarm.
6 Output configured as Flashing light.
7 Output configured as Latch.
8 Output configured as Magnetic lock.
9 Output configured as Maintenance.
10 Output configured as Flashing Light and Maintenance.
11 Output configured as Traffic Light control with TLB board.
12 Output configured as Antitampering
13 Output configured as Gate Status
14 Output configured as Bistable Radio Channel
15 Output configured as timed Radio Channel
0 Pre-flashing switched off.
1 Red lights flash, for 3 seconds, at start of operation.
0 Red lights off when gate closed.
1 Red lights on when gate closed.
Optional extras