Important Notice; Intended Use; Assembly And Adjustments - DeWalt D26950 Manual De Instrucciones

English
2. Remove or cover any carpets, rugs, furniture, clothing,
cooking utensils and air ducts.
3. Place drop cloths in the work area to catch any paint
chips or peelings. Wear protective clothing such as extra
work shirts, overalls and hats.
4. Work in one room at a time. Furnishings should be
removed or placed in the center of the room and
covered. Work areas should be sealed off from the rest
of the dwelling by sealing doorways with drop cloths.
5. Children, pregnant or potentially pregnant women and
nursing mothers should not be present in the work area
until the work is done and all clean up is complete.
6. Wear a dust respirator mask or a dual filter (dust and
fume) respirator mask which has been approved by
the Occupational Safety and Health Administration
(OSHA), the National Institute of Safety and Health
(NIOSH), or the United States Bureau of Mines. These
masks and replaceable filters are readily available at
major hardware stores. Be sure the mask fits. Beards
and facial hair may keep masks from sealing properly.
Change filters often. DisPOsABlE PAPER MAsKs ARE
nOT ADEQUATE.
7. Use caution when operating the heat gun. Keep the
heat gun moving as excessive heat will generate fumes
which can be inhaled by the operator.
8. Keep food and drink out of the work area. Wash hands,
arms and face and rinse mouth before eating or
drinking. Do not smoke or chew gum or tobacco in the
work area.
9. Clean up all removed paint and dust by wet mopping
the floors. Use a wet cloth to clean all walls, sills and
any other surface where paint or dust is clinging. DO
nOT sWEEP, DRY DUsT OR VACUUM. Use a high
phosphate detergent or trisodium phosphate (TSP) to
wash and mop areas.
10. At the end of each work session put the paint chips and
debris in a double plastic bag, close it with tape or twist
ties and dispose of properly.
11. Remove protective clothing and work shoes in the work
area to avoid carrying dust into the rest of the dwelling.
Wash work clothes separately. Wipe shoes off with a wet
rag that is then washed with the work clothes. Wash
hair and body thoroughly with soap and water.

IMPORTANT NOTICE

In order for this tool to be an effective paint stripper, it must
produce extremely high temperatures. As a consequence, the
stripper is capable of igniting paper, wood, paint and varnish
residue and similar materials.
As you become more familiar with the tool and develop the
proper technique, the danger of accidental ignition will be
greatly reduced. In establishing the proper technique, the best
thing to do is PRACTICE! Work on simple stripping projects,
preferably outdoors, until you get a "feel" for how to use your
stripper safely and effectively.
4
As You Practice, Observe the Following
Procedures for Safety
• Always be sure the tool is turned off and disconnected
from power supply when unattended.
• Clean the scraper blade often during use. Built up residue
on the blade is highly flammable.
• Experiment to find the optimum distance from the tool's
nozzle to the surface being stripped. This distance [1"–2"
(25.4 mm–50.8 mm)] will vary depending on the material
being removed.
• Keep the heat gun moving ahead of the scraper blade at
all times.
• As you work, clean up loose pieces of paint as they
accumulate around the work area.
• When working indoors, keep away from curtains, papers,
upholstery and similar flammable materials.
• Above all, remember that this is a serious tool that is
capable of producing excellent results when used properly.
Practice on simple projects until you feel comfortable
with your stripper. Only then will you have mastered the
proper technique.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. D
if this tool does not operate, check power supply.
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

Intended Use

Your D WALT heat gun has been designed for stripping
e
paint, soldering pipes, shrinking PVC, welding and bending
plastics as well as general drying and thawing purposes.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
The heat gun is a professional power tool. DO nOT let
children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Air Temperature (Fig. A)
D26950
The air temperature can be adjusted to suit a wide range of
applications. Turn the air temperature adjustment knob
clockwise or counterclockwise for higher or lower heat.
WALT tools are factory tested;
e
4