Replacing The Light Bulb - SCHOLTES SCHXL 897E D E Manual De Instrucciones

3. Grip the door on the two outer sides and
close it approximately half way. Pull the
door towards you, lifting it out of its slot (see
diagram). To replace the door, reverse this
sequence.
Inspecting the seals
Check the door seals around the oven regularly. If the seals are damaged,
please contact your nearest Service Centre (see Assistance). We recommend
that the oven is not used until the seals have been replaced.

Replacing the light bulb

Lamp
Holder
compartment
Lamp
Glass cover
! Do not touch the light bulb directly with your hands.
! Do not use the oven lamp as/for ambient lighting.
Automatic cleaning using the Diamond Clean cycle
The Diamond Clean mode is an automatic cleaning cycle which releases
steam inside the cavity and uses the exclusive Diamond Clean enamel to
make it easy to remove any dirt residues from the cavity and accessories.
Available in three different levels: Economy, Normal and Intensive - to be
used based on the type of dirt.
The Diamond Clean cycle can be used to keep the oven always clean.
During the cleaning process steam is released inside the cavity which, together
with the titanium-based Diamond Clean enamel (on the inside walls of the
oven and dripping pans), makes it easy to clean the oven.
Three different cleaning levels may be selected: Economy, Normal and
Intensive - based on the type of dirt. The following are the features of the
three different cycles.
In order to start the Diamond Clean cycle:
1. Wait for the oven to cool down.
2. Place the dripping pan on level 1 and pour in the following quantities of
water: 150g for the Economy cycle, 250g for the Normal cycle and 350g for
the Intensive cycle. A smaller or larger quantity of water than recommended
may affect the cycle results. Do not use detergents.
3. Close the oven door.
4. Press the icon to switch on the control panel.
F
To replace the oven light bulb:
1. Remove the glass cover of the
lamp-holder.
2. Remove the light bulb and replace
it with a similar one: halogen lamp
voltage 230 V, wattage 25 W, cap G 9.
3. Replace the glass cover (see
diagram).
5. Press the icon to display the text "dc", "nor" and the default duration
of 15 minutes (normal cycle) alternately.
6. Press the icon and turn the TIMER knob to adjust the default cleaning
level. There are 3 different levels to choose from, each with a pre-set duration
which cannot be changed:
1. Economy (ECO): turn the knob towards " ". Duration 10 minutes.
2. Normal (NOR): initial level. Duration 15 minutes.
3. Intensive (INT): turn the knob towards " ". Duration 20 minutes.
4. Press the icon to confirm.
5. Press the icon to start the cleaning process.
! To prevent any steam leaks do not open the door during the cycle.
! In the last minutes of the intensive cycle the control panel will partially and
momentarily mist up. The mist will disappear every time the tangential cooling
fan is started.
An end time for the Diamond Clean cycle may be programmed just like for a
normal cooking cycle (see Programming the automatic cleaning end time.)
Safety devices
• Press the button to cancel the cleaning cycle at any time;
• If an anomaly occurs, the heating elements will be switched off.
Programming the automatic cleaning end time
1. Press the icon twice. The icon
flash on the display panel;
2. Turn the TIMER knob towards " " and " " to adjust the cleaning end
time value.
3. Once you have reached the desired end time, press again the icon
. The display panel will show the duration, the cleaning end time and the set
cleaning level alternately.
4. Press the icon to start programming.
Programming has been completed when the icons
5. Once the cleaning process is over, "END" appears on the display panel
and a buzzer sounds.
• E.g. It is 9:00 a.m. and the Economy Diamond Clean level has been
selected, with the default duration of 10 minutes. 12:30 p.m. is scheduled
as the end time. The programme will start automatically at 12:20 p.m.
To cancel a programme press the icon
Once the automatic cleaning cycle is over
Wait for the oven to cool down and remove any water residues using a
non-abrasive sponge. Waiting more than 10 minutes before carrying out this
operation may affect the results.
To remove stubborn dirt we recommend repeating the Intensive cycle by
adding a few detergent drops to the water.
and numerical digits begin to
and light up.
.
35
GB