The Service Setting Menu - Sony VPH-D50HTU Manual De Instalación

Using the MENU

The SERVICE SETTING Menu

The SERVICE SETTING menu is used for
adjustments performed in service adjustment mode.
"S" appears at the top left corner of the menu,
indicating service adjustment mode.
Page 1
S
I N T . O S C P A T T E R N : P 2
SERVICE
SETTING I N T . O S C M O D E : O F F
D I R E C T P O W E R O N : O F F
SET
INFO. R S - 4 2 2 A : 3 8 . 4 K
ABL
LINK
SEL: SET:
ENTER
Page 2
S
P O W E R O N D E L A Y : O F F
SERVICE SERVICE
SETTING SETTING P I C . O R B I T I N G : O F F
A L L W H I T E M O D E :
SET SET
INFO. INFO.
ABL ABL
LINK LINK
SEL: SET:
ENTER
INT. (internal) OSC (oscillation) PATTERN
Selects the oscillation frequency pattern generated
with the internal oscillator.
The horizontal and vertical frequencies for the selected
pattern are displayed in the pop-up menu on the
screen.
S
I N
I N T . O S C P A T T E R P 0
SERVICE
SETTING I N T . O S C M O D E : O P 1
D I R E C T P O W E R O P 2
SET
INFO. R S - 4 2 2 A : 3 8 . 4 K
UNI
FORMITY f H = 1 5 . 7 K H z
f V = 6 0 H z
ABL
LINK
SEL: SET:
ENTER EXIT: MENU
P0: fH = 15.7 kHz, fV = 60 Hz
P1: fH = 24.8 kHz, fV = 56 Hz
P2: fH = 31.5 kHz, fV = 60 Hz
P3: fH = 48.3 kHz, fV = 60 Hz
P4: fH = 64.0 kHz, fV = 60 Hz
52
(GB) Before adjustment
I N P U T - A
EXIT: MENU
I N P U T - A
2 0 m i n
EXIT: MENU
INT. (internal) OSC (ocillation) MODE
Set to ON to activate the internal oscillator.
S
I N P U T - A
I N T . O S C P A T T E
SERVICE
SETTING I N T . O S C M O D E : O N
D I R E C T P O W E R O F F
SET
INFO. R S - 4 2 2 A : 3 8 . 4 K
ABL
LINK
SEL: SET:
ENTER EXIT: MENU
Note
When no signal is input, you cannot select this item.
DIRECT POWER ON
Set to ON to turn on the projector by pressing the
MAIN POWER switch on the projector. Set to OFF to
enter standby mode by pressing the MAIN POWER
switch.
S
I N P U T - A
I N T . O S C P A T T E R N : P 1
SERVICE
SETTING I N T . O S C M O D E
D I R E C T P O W E R O N
SET
INFO. R S - 4 2 2 A : 3 8 . 4 O F F
ABL
LINK
SEL: SET:
ENTER EXIT: MENU
Note
When the projector is in standby mode (it is turned off by
pressing the POWER OFF key on the remote control) with
DIRECT POWER ON set to ON, the projector will be
turned on automatically if the power interruption occured
and has been restored.
RS-422A
Sets the communication baud rate for the RS-422A
terminal to 38.4K, 19.2K, 9600 or 4800.
S
I N P U T - A
I N T . O S C P A T T E R N : P 1
SERVICE
SETTING I N T . O S C M O D E : O F F
D I R E C T P O W E R O N : O F F
SET
INFO. R S - 4 2 2 A : 3 8 . 4 K
1 9 . 2 K
ABL
LINK 9 6 0 0
4 8 0 0
SEL: SET:
ENTER EXIT: MENU