Smalvic FI-74MT Manual De Instrucciones página 19

Switching on
Commissioning/restoring power cut
All icons remain on for 2 secs. to verify oven operation.
Whether it concerns the first connection to the mains or
restoring voltage, the system time is as shown in the figure, with
flashing numbers-
To continue, the system time must be set (see reference
paragraph).
If the cooking mode is interrupted due
to a power cut, the oven maintains all
the information regarding the cooking
(blackout mode).
Once the oven system time has been
set, the acoustic signal blocks and
goes to PAUSE mode
paragraph).
Adjusting system time
The system time (clock) is based on the type of mains power
supply (50Hz or 60Hz). Time adjustment takes place with oven
OFF:
• Hold key 6 down for at least 3 seconds: the digits of the
hour flash on the display. Use keys 4 and 5
value.
• For the acquisition of the time set, it must be confirmed using
key 6 .
• Perform the same procedure to set the minutes.
If the oven is OFF, the control then shows just the system time,
dimming after 1 min.
If the oven is in blackout mode due to a lack of voltage, the time
digits already flash: operate on keys 4 and 5
as specified above.
The oven is activated by pressing key 1 ON/OFF
2 sec and switches off by touching the same key.
If no keys are pressed after switch-on, the oven deactivates
automatically after 1 min. (accidental switch-on control).
Oven ON: single acoustic signal.
Oven OFF: double acoustic signal.
If the oven is off in low consumption mode (dimmed display
light), at the first touch of a key, we have RESUME mode. The
low consumption mode is re-enabled automatically after one
minute.
ATTENTION
Oven switch-off annuls all cooking programming and
times set.
Accidental switch-on control
It is an automatic oven switch off signal. This takes place after
oven switch on using key 1 ON/OFF
inactivity, i.e. no function selected and activated. After 1 minute,
a double acoustic signal will inform of switch-off.
INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS
Oven on: in stand-by for commands
By pressing key 1 ON/OFF
to receive settings on the desired cooking function.
Ventilated cooking is the default function (Circular Resistance +
Radial Fan) with pre-set temperature equal to 180°C.
Using key 2 menu
(see reference
of display:
• cooking functions menu;
• oven temperature;
• cooking time programming;
• timer;
• alarm clock;
When scrolling the functions, the relative icons flash. If the
function is not confirmed or modified within 7 secs, the selection
is deactivated. From oven "on in stand-by for commands", if
commands are inactive for a time exceeding 5 minutes, the
oven switches off automatically.
to set the
to set the time
Cooking functions menu
for at least
After oven switch-on using key 1 ON/OFF
directly access the choice of cooking functions by pressing key
2 menu
flash.
Using keys 4 and 5
cooking functions available (see " COOKING FUNCTIONS TO BE
SELECTED"): the relative segments activate.
Once the desired function is highlighted, confirm with key
In each case, after 7 seconds of inactivity of the commands,
the function selected is confirmed automatically (auto-confirm).
At this point, to start cooking, confirm everything using key 3
START
The oven starts the pre-heating phase. The light inside the oven
switches on
starts to flash. On the basis of the cooking function selected,
the default temperature appears and the upward temperature
icon
mode is displayed. The respective icon
figure).
and 1 min of commands
BUILT-IN ELECTRIC OVENS
the oven switches on while waiting
the functions can be scrolled in this order
ATTENTION
It is possible to pass from oven "in cooking mode" to the
"on in stand-by for commands" status by pressing key 1
ON/OFF . Pressing the key again, switches the oven
off definitively.
. The central icon and the cooking functions start to
it is possible to scroll through all
(see reference paragraph)
. The cooking pan icon
starts to flash. The progressive cooking time in manual
EN
, it is possible to
.
sis activated and
starts to flash (see
17