Important Safety Instructions - Powermatic PM-2X2R Instrucciones De Operación

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

1.0 IMPORTANT SAFETY
INSTRUCTIONS
When
using
an
electrical
precautions should always be followed, including
the following.
WARNING – To reduce risk of injury:
1.
Read and understand the entire owner's
manual
before
operation.
2.
Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3.
Replace the warning labels if they become
obscured or removed.
4.
This CNC routing machine is designed and
intended for use by properly trained and
experienced personnel only. If you are not
familiar with the proper and safe operation of a
CNC routing machine, do not use until proper
training and knowledge have been obtained.
5.
Do not use this machine for other than its
intended use. If used for other purposes,
Powermatic disclaims any real or implied
warranty and holds itself harmless from any
injury that may result from that use.
6.
Always wear approved safety glasses/face
shield while using this routing machine.
Everyday
eyeglasses
resistant lenses; they are not safety glasses.
7.
Before operating this machine, remove tie,
rings, watches and other jewelry, and roll
sleeves up past the elbows. Do not wear loose
clothing. Confine long hair. Non-slip footwear or
anti-skid floor strips are recommended. Do not
wear gloves.
8.
Wear ear protectors (plugs or muffs) during
extended periods of operation.
9.
Drilling, sawing, sanding or machining wood
products generates wood dust and other
substances known to the State of California to
cause cancer. Avoid inhaling dust generated
from wood products or use a dust mask or other
safeguards to avoid inhaling dust generated
from wood products.
10. Wood products emit chemicals known to the
State of California to cause birth defects or
appliance,
basic
attempting
assembly
only
have
impact
other reproductive harm. (California Health and
Safety Code Section 25249.6)
11. Do not operate this machine while tired or under
the influence of drugs, alcohol or any
medication.
12. Make certain the switch is in the OFF position
before connecting the machine to the power
supply.
13. Make certain the machine is properly grounded.
14. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
or
15. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine
before turning it on.
16. Keep safety guards in place at all times when
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
17. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced.
18. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
19. Keep the floor around the machine clean and
free of scrap material, oil and grease.
20. Keep visitors a safe distance from the work
area. Keep children away.
21. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
22. Give your work undivided attention. Looking
around, carrying on a conversation and "horse-
play" are careless acts that can result in serious
injury.
23. Maintain a balanced stance at all times so that
you do not fall into the cutter or other moving
parts. Do not overreach or use excessive force
to perform any machine operation. Keep hands
away from rotating cutting tool.
24. Use the right tool at the correct speed and feed
rate. Do not force a tool or attachment to do a
job for which it was not designed. The right tool
will do the job better and more safely.
2
Tabla de contenido
loading

Este manual también es adecuado para:

Pm-2x4sp

Tabla de contenido