DeWalt DWE46152 Manual De Instrucciones página 8

English
5. When surface grinding is complete, turn the tool off and
disconnect from the power source. Allow the tool to
stop rotating before laying it down.
nOTE: The surface grinding shroud and dust extractor
vacuum will only be effective when used with a diamond
surface cup wheel on a flat surface.
Installation of the bail handle assembly
1. Lightly pull thumbscrews outwards from handle so that
their threaded ends are pulled inside handle.
2. Place the handle assembly over the grinder gear case
aligning the thumbscrews with the threaded holes
and the ears on the gear case with the slots in the bail
handle assembly.
3. Tighten the thumbscrews to secure the handle to
the grinder.
Adjustment of the bail handle angle
1. Loosen both thumbscrews 2 full turns.
2. Rotate the handle to the desired 45˚ or 90˚ position
making sure that the detent groves align.
3. Re-tighten the thumbscrews to secure the handle to
the grinder.
Edging Use Application (Fig. A)
This concrete grinding shroud has a door feature to allow
flush grinding against a wall.
1. Turn off the tool and disconnect from the power source.
2. Using the edging door tab
until it snaps into the open postion.
3. Connect the tool to the power source.
4. Position hands and body away from wheel and
door opening.
5. Place the door edge flush to work surface, turn the tool
on and begin grinding. Remove the tool from work
surface before turning the tool off.
6. When flush grinding is complete, turn off the tool and
disconnect from power source. Allow the tool to stop
rotating before laying it down.
7. Using the edging door tab
into the closed position.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury. This applies
to both the grinder and the dust extractor
vacuum. Such preventative safety measures reduce
the risk of starting the tool accidentally.
Replace Brush Skirt (Fig. A)
1. Turn off the tool and disconnect from power source.
2. Push worn brush skirt from brush skirt removal holes
3. Press new brush skirt into brush skirt removal holes
until secure.
6
, rotate the edging door
6
6 , rotate door until it snaps
4 .
Replacement brush skirts are available at extra cost from
your local dealer or authorized service center. If you need
assistance in locating any accessory, please contact D
Industrial Tool Co., 701 East Joppa Road, Towson, MD
21286, call 1–800–4-D WALT (1–800–433–9258) or visit our
e
website: www.D WALT.com.
e
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D WALT authorized service center.
e
Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
WARRAnTY sERViCE: Registering your product will
•
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
WALT
e
WALT
e
WALT Industrial
e
WALT factory
e