Tabla de contenido
Idiomas disponibles
Idiomas disponibles
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits, etc.
in accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Surface Grinding Shroud Safety Rules
•
The shroud must be securely attached to the power
tool and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator.
The shroud is designed to collect dust and help protect the
operator from accidental contact with the wheel.
•
Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can
be attached to your power tool, it does not assure
safe operation.
•
Only use dry diamond surface cup wheels with this
surface grinding shroud. The surface grinding shroud
is not intended to be used with standard grinding, cut-off,
cup wheels or wire brushes.
•
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed can
break and fly apart.
•
Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and shock
the operator.
•
Always use side or bail handle. Tighten the handle
securely. The handle should always be used to maintain
control of the tool at all times.
•
Do not use a damaged accessory. Before each use
inspect the accessory such as diamond wheel for
chips and cracks, backing pad for cracks and tear or
excess wear. If power tool or accessory is dropped,
inspect for damage or install an undamaged
accessory. After inspecting and installing an
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run
the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break apart
during this test time.
•
When starting the tool with a new or replacement
wheel, hold the tool in a well protected area and let
it run for one minute. If the wheel has an undetected
crack or flaw, it should burst in less than one minute.
Never start the tool with a person in line with the wheel.
This includes the operator.
•
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask or
respirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
•
Position the cord clear of the spinning accessory. If
you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
•
Never lay the power tool down until the accessory
has come to a complete stop. The spinning accessory
may grab the surface and pull the power tool out of
your control.
•
Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
Regularly clean the power tool's air vents. The
•
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
•
Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
Do not use accessories that require liquid coolants.
•
Using water or other liquid coolants may result in
electrocution or shock.
•
DO NOT use wire brushes with this surface
grinding shroud.
•
DO NOT use abrasive wheels.
•
DO NOT grind or cut metal with a diamond cup
wheel. Fragments could loosen and fly apart.
•
ALWAYS use with a dust collector.
WARNING: When not in use, place grinder
on a stable surface where it will not move
inadvertantly, roll or cause a tripping or falling
hazard. Serious personal injury may result.
Additional Safety Information
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
•
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•
ANSI S12.6 (S3.19) hearing protection,
•
NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
English
3
Tabla de contenido
