Clarion DXZ948RMP Manual De Instrucciones página 11

AC-Processor III Operations
CAR LENGTH:
Adjusts the deviation in sound pressure along
the length of the car.
1. Press the [SOUND] button.
2. Touch VSE.
3. Touch on the ON/OFF display.
The VSE effect is toggled ON/OFF.
4. Touch B/U to select "BASIC" or "USER".
5. Touch on the right of the display to
select the menu that is used as the menu for
adjustment.
6. Press the [A] button.
7. Touch on the adjustment item display
to select "DIFFUSE", "CAR WIDTH" or "CAR
LENGTH".
VSE EDIT
RTN
D I FFUSE
5
8. Touch on the right of the display and
adjust the item as desired.
∗ This item can be adjusted within the range
1 to 10.
9. Repeat steps 7 and 8 to adjust the desired
item.
10. When you have finished adjusting each item,
touch RTN.
The display returns to the original screen,
and " " is displayed at the BASIC or USER
display.
Operation so far completes VSE adjustment.
To continue to store the adjustment values to
the VSE user menu, perform the following.
11. Touch and hold RTN for 1 second or longer.
The VSE user menu list is displayed.
12. Touch and hold the user memory you want
to store the adjustment values to for 2
seconds or longer.
You will hear a long beep, and the values
you adjusted up to step 9 are stored to the
VSE user menu.
If you hear a short beep, the adjustment
values up to step 9 are discarded. Adjust
these values again as required.
13. Touch RTN.
14. Press the [SOUND] button to return to the
original mode.
∗ To select a stored user memory, touch B/U
to display "USER" and touch on the
user memory No.
20
DXZ948RMP
Selecting the P.EQ menu
P.EQ (Parametric Equalizer) allows you to
compensate the entire frequency level range in
detail by smooth curve using frequency
compensation matched to the type of your car.
In the "Selecting each mode" procedure (cf.
page 44), set EQ SELECT to "P.EQ".
• The factory default setting for P.EQ is "OFF"
and for the P.EQ basic menu is "SEDAN-1".
P.EQ basic menu
6 types of P.EQ basic menu are pre-stored to
this function matched to the type of your car and
the speaker mounting position. Select the basic
menu to suit you car.
1. Press the [SOUND] button.
2. Touch P.EQ.
OFF OFF OFF
POSITION P. EQ Dolby PL II
RTN
SOUND MENU
2 - ZONE ADF A - MODE
OFF OFF
3. Touch on the ON/OFF display.
The P.EQ effect is toggled ON/OFF.
P.EQ MODE
RTN
SEDAN - 1
BASIC
2 6
1 BU
OFF
B / U
When the P.EQ effect is set to "OFF", the
P.EQ setting is not reflected on the music
source. This ends the P.EQ setting. Press
the [SOUND] button to return to the original
mode.
4. Touch B/U to select "BASIC".
P.EQ MODE
RTN
SEDAN - 1
BASIC
2 6
BU
ON 1
B / U
Each touch of B/U toggles between "BASIC"
and "USER".
5. Touch on the P.EQ basic menu No. to
select the P.EQ basic menu.
P.EQ basic menu
Speaker Mounting
No. Display name
position
1 SEDAN-1 Front: Front door
Rear: Rear parcel
2 SEDAN-2 Front: Front door
Rear: Rear door
3 WAGON-1 Front: Front door
Rear: Luggage (side)
4 WAGON-2 Front: Front door
Rear: Rear door
5 MINI VAN-1 Front: Front door
Rear: Luggage (side)
6 MINI VAN-2 Front: Front door
Rear: Rear door
6. Press the [SOUND] button to return to the
original mode.
Adjusting/storing P.EQ
(user memory)
With user memory, you can compensate the
frequency characteristics to suit your car based
upon the P.EQ basic menu. Up to 6 adjustment
setups can be stored to user memory. For
details, see "P.EQ adjustment" .
1. Press the [SOUND] button.
2. Touch P.EQ.
3. Touch on the ON/OFF display.
The P.EQ effect is toggled ON/OFF.
4. Touch B/U to select "BASIC" or "USER".
5. Touch on the right of the display to
select the menu that is used as the menu for
adjustment.
6. Press the [A] button.
7. Touch on the left of the display to
select "FRONT" or "REAR".
P.EQ EDIT
RTN
BAND 1
FRONT
8. Touch on the centre of the display to
select each adjustment item.
Each touch of switches the
adjustment item as follows:
Adjustment items
BAND FREQ Q GAIN BAND...
AC-Processor III Operations
9. Touch on the right of the display and
adjust the item as desired.
∗ "BAND" can be adjusted within the range
1 to 3.
∗ "FREQ" can be adjusted within the range
20Hz to 20kHz.
∗ Select one of 1, 3, 5, 7, or 20 as "Q".
∗ "GAIN" can be adjusted within the range
-12dB to +12dB.
10. Repeat steps 7 to 9 to adjust the desired
item.
11. When you have finished adjusting each item,
touch RTN.
The display returns to the original screen,
and " " is displayed at the BASIC or USER
display.
Operation so far completes P.EQ
adjustment. To continue to store the
adjustment values to the P.EQ user menu,
perform the following.
12. Touch and hold RTN for 1 second or longer.
The P.EQ menu list is displayed.
13. Touch and hold the user memory you want
to store the adjustment values to for 2
seconds or longer.
You will hear a long beep, and the values
you adjusted up to step 10 are stored to the
P.EQ user menu.
If you hear a short beep, the adjustment
values up to step 10 are discarded. Adjust
these values again as required.
14. Touch RTN.
15. Press the [SOUND] button to return to the
original mode.
∗ To select a stored user memory, touch B/U
to display "USER" and touch on the
user memory No.
P.EQ adjustment
The settings that can be adjusted in the P.EQ
menu are as follows. The centre frequency, gain
and Q curve can be stored to channel/band
combinations.
For example, centre frequency "250Hz", gain
"-8dB" and Q curve "3" can be stored to band 1
on the front.
FRONT/REAR (channel selection)
Selects the channel (front or rear) to adjust.
BAND (band selection)
Selects the frequency band (1 to 3) to adjust.
Set the centre frequency (FREQUENCY), gain
(GAIN) and Q curve (Q) for each frequency
band.
DXZ948RMP
21