Important - Sears Kenmore 11026132410 Instrucciones De Instalación

Parts needed: (Not supplied with washer)
Inlet hoses with
flat washers
To order, please refer to toll-free phone numbers on back page
of your Use and Care Guide.
• 8212656RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack)
• 8212641 RP 5 ft. (1.5 m) Inlet hose, Black EPDM (2 pack)
• 8212546RP 4 ft. (1.2 m) Inlet hose, Black EPDM (2 pack)
• 8212545RP 5 ft. (1.5 m) Inlet hose, Red and Blue EPDM
(2 pack)
• 8212487RP 5 ft. (1.5 m) Nylon braided inlet hose (2 pack)
• 8212638RP 6 ft. (1.8 m) Nylon braided inlet hose, space
saving 90 ° elbow, hypro-blue steel couplings
(2 pack)
• 8212637RP 6 ft. (1.8 m) Inlet hose, Black EPDM, space
saving 90 ° elbow, hypro-blue steel couplings
(2 pack)
Alternate parts: (Not supplied with washer)
Your installation may require additional parts. To order, please
refer to toll-free numbers on back page of your Use and Care
Guide.
If you have:
Overhead sewer
1" (25 mm) standpipe
Drain hose too short
Lint clogged drain
You will need:
Standard 20 gal. (76 L) 39" (990 ram)
tall drain tub or utility sink, sump
pump and connectors (available from
local plumbing suppliers)
2" (51 mm) diameter to 1" (25 mm)
diameter Standpipe Adapter
Part Number 3363920
Connector Kit Part Number 285835
Extension Drain Hose Part
Number 285863
Connector Kit Part Number 285835
Drain Protector Part Number 367031
Connector Kit Part Number 285835
LOCAT(ON REQU(REMENTS
Select proper location for your washer to improve performance
and minimize noise and possible "washer walk", Install your
washer in a basement, laundry room, closet, or recessed area,
43 'l
(1092 mm)
(648 mm)
You will need:
• A water heater set to 120 ° F (49° C).
• A grounded electrical outlet located within 4 ft (1.2 m) of
power cord on back of washer.
• Hot and cold water faucets located within 3 ft (0.9 m) of hot
and cold water fill valves on washer, and water pressure
of 20-100 psi (138-690 kPa).
• A level floor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet is not recommended.
• Floor must support washer's total weight (with water and load)
of 315 Ibs (143 kgs).
IMPORTANT: Do not install, store, or operate washer where it
will be exposed to weather or in temperatures below 32 ° F (0° C).
Water remaining in washer after use may cause damage in tow
temperatures. See "Washer Care" in your Use and Care Guide
for winterizing information.
Proper installation is your responsibility.
Recessed area or closet installation
3 II
(76 ram)
_1 _-_
14
max,
(356 mm)
19"
, ,_i
;;,_I
I
II
' N', i',i_l II
,, I ii
...2 .i
II
mmj .: I II
(25 mm)
24 in. 2
1155cm2}
176mm)
Dimensions show recommended spacing allowed, except for
closet door ventilation openings which are minimum required.
This washer has been tested for installation with spacing of
0" (0 mm) clearance on the sides. Consider allowing more space
for ease of installation and servicing, and spacing for companion
appliances and clearances for walls, doors, and floor moldings.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed, top
and bottom air openings in door are required.