Working - Festool CLEANTEX CTL 26 E Manual De Instrucciones Original/Lista De Piezas De Repuesto

CLEANTEX CTL/ CTL AC
GB
7.3 Adjusting the suction power
You can use the suction power adjuster
to adapt the machine suction power to differ-
ent applications.
7.4 Applying the brake
Folding out the black brake lever
vents the mobile dust extractor from rolling.
To achieve this, lift the front end of the mo-
bile dust extractor slightly and push the
black brake lever downwards until it latches
into place. Push the green lever
to release.
7.5 Temperature cut-out
To prevent overheating, a temperature cut-
out switches the mobile dust extractor off
when it reaches a critical temperature.
X Switch off the mobile dust extractor and
allow to cool for about 5 minutes.
L If the mobile dust extractor will not switch
on again, please contact a Festool service
workshop.
7.6 Changing the filter bag
Removing the filter bag
X
Open the locking clips
the top section of the machine[2-1].
X Remove the filter bag.
X
Dispose of the used filter bag in accor-
dance with statutory regulations.
X
Clean the dust container [2-3].
Inserting the filter bag
X
Insert a new filter bag (FIS-CT 26/36) in
the inlet port of the dust container and in-
terlock it. Important: be aware that the
locking engages.
X
Replace the top section
the locking clips [2-2].
L Make sure that the filter bag is not
pinched between the top and bottom sec-
tions.
7.7 Changing the disposal bag
Removing the disposal bag
X Open the locking clips
the top section of the machine[2-1].
X
Close the disposal bag.
X
Remove the disposal bag.
X Dispose of the used disposal bag in accor-
dance with statutory regulations.
X
Clean the dust container [2-3].
16
[1-9]
[1-13] pre-
[1-12] again
[4]
[2-2] and remove
[5]
[2-1] and close
[6]
[2-2] and remove
Inserting the disposal bag
X Insert a new disposal bag (ENS-CT26/36)
on the inlet nozzle of the container and
lock in position.
Important: The lateral openings on the
disposal bag must be positioned inside the
container. Make sure that the bolt engag-
es.
X Place the disposal bag over the edge of
the container.
Make sure that the contacts
free.
X
Replace the top section
the locking clips [2-2].
8

Working

8.1 Handling
Hose store: after finishing work, you can
feed the suction hose through the recess
3] and place it in the hose store. You can do
the same with the mains cable through the
other recess [8-2].
SysDoc Systainer attachment system: a
Systainer can be attached to the storage
area via the two slides [8-1].
8.2 AUTOClean - Cleaning the main
filter (only versions with Auto-
Clean)
To maintain a constant suction power when
extracting fine dust, you can adjust the fre-
quency of the automatic
tem in infinite variables using the rotary
knob. Always use the automatic cleaning
system in combination with a disposal bag
(in line with dust class 'L' requirements).
Before performing wet extraction tasks
or working with a filter bag, set the
7] rotary knob to position 0.
X Set the automatic cleaning function to the
highest setting when
large quantities of dust.
Manual cleaning
If the suction power decreases, clean-
ing can be started manually by turning
the switch [1-8]
sitioned on either side of the switch.
We recommend cleaning the main filter
completely if severely clogged:
X
Set the suction power adjuster
the maximum setting.
X Cover the end of the nozzle or suction
hose with your hand for 10 seconds.
[7]
[10-2] are
[2-1] and close
[8-
[1-7] cleaning sys-
[1-
[1-7] extracting
to the AC symbol po-
[1-9] to