Technical Data; Before Starting The Equipment - EINHELL BG-SC 2240 P Manual De Instrucciones

Anleitung BG_SC_2240_P_SPK7:_

4. Technical data

Engine type:
Displacement
Max. engine output
Working speed
Fuel:
Tank capacity:
Engine oil:
Spark plug:
Blades (number)
Blade diameter
Depth setting
Working width:
L sound pressure level
pA
L sound power level
WA
Vibration a
hw
Weight:

5. Before starting the equipment

The equipment is delivered unassembled. The grass
basket and the complete push bar must be
assembled and mounted before using the equipment.
Follow the operating instructions step-by-step and
use the pictures provided as a visual guide to easily
assemble the equipment.
Fitting the bottom push bar (Fig. 3)
Fit the bottom push bar (Fig. 3 / Item 3) to the push
bar holder using the screws (Fig. 3 / Item 9) and nuts
(Fig. 3 / Item 10) supplied.
Fitting the top push bar holder (Fig. 4)
Position the upper push bar (Fig. 4 / Item 2) such that
its holes line up with the holes of the lower bar. Screw
the tubes together, using the screws (Fig. 4 / Item 12)
and nuts (Fig. 4 / Item 8) supplied. Use the supplied
cable clips (Fig. 4 / Item 11) to secure the throttle
cable and the engine Start / Stop cable to the lower
push bar.
Fitting the debris box (Fig. 5)
Lift the ejector flap (Fig. 5 / Item 5) with one hand and
attach the debris box (Fig. 5/Item 6) to the handle
from above using your other hand.
29.03.2012 13:39 Uhr
Important: Before you attach the debris box you
must ensure that the engine is switched off and the
roller is not rotating.
1 cylinder, 4-stroke
118 cc
6. Starting up
2.2 kW / 3 hp
3,600 rpm
Important!
Unleaded petrol
The engine does not come with oil in it.
Therefore, ensure that you add oil before starting
approx. 2.5 l
it up. The oil level in the engine must be checked
approx. 0.4 l / 10W30
each time before mowing. (see Checking the oil
LG F7TC
level).
18
Starting the equipment (Fig. 6 – 7)
163 mm
In order to avoid any unintentional start-ups of the
-15 - +5 mm
engine, it comes equipped with an engine brake (Fig.
6/Item 1) which must be pressed at all times whilst
400 mm
the device is in use, otherwise the engine will stop.
81 dB(A), K = 3dB (A)
Important: When the engine brake lever is released
96 dB(A) it must return to its initial position and the engine
must stop. If this is not the case, do not use the
3,492 m/s 2 , K = 1,5 m/s 2
equipment again.
31 kg
1. Open the petrol cock (Fig. 7 / Item B). Set the
2. Set the choke lever (Fig. 7/Item C) to the
3. Move the throttle lever (Fig. 1 / Item 7) to the
4. Press the engine brake lever (Fig. 6 / Item 1) and
5. Allow the engine to warm up briefly and then set
6. The speed of the cutter unit can be controlled
Important: Always pull the starter cable slowly until
you feel the initial resistance before you then pull it
quickly to start the engine. Do not allow the starter
cable to whip back of its own accord.
Important: The scarifier roller begins to rotate as
soon as the engine is started.
Important! Never open the ejector flap when the
motor is running. A rotating cutting unit can cause
injuries.
Always fasten the ejector flap carefully. The flap flips
back to the "Closed" position by the tension springs!
Always ensure that a safe distance (provided by the
long handles) is maintained between the user and
the housing. Be especially careful when scarifying
Seite 15
cock to "ON" for this purpose.
"Choke" position.
center position.
pull the starter cable (Fig. 7 / Item A) forcefully
until the engine starts.
the choke lever (Fig. 7 / Item B) to the "RUN"
Position.
using the throttle lever (Fig. 6 / Item 7) (tortoise =
slow / rabbit = fast).
GB
15