Tabla de contenido
Idiomas disponibles
Idiomas disponibles
K-380 Drain Cleaning Machine
To Install Replacement Cable
NOTE! To make cable installation easier, completely
uncoil new cable before proceeding. Also, a 30
degree bend about 4 inches from back end of
cable will facilitate it entering the drum.
1. Insert about 24 inches of cable through the guide
tube into the drum.
IMPORTANT: Cable should coil into the drum in a
counter-clockwise direction (Figure 9) .
Figure 9 – Coil Cable Into Drum As Shown
2. Reach inside the drum and maneuver cable so that it
is under the cable bracket.
3. Retighten the screw to clamp the cable against the
back wall of the drum.
Accessories
Only the following RIDGID products have
WARNING
been designed to function with the K-380 Drain Cleaning
Machine. Other accessories suitable for use with other
tools may become hazardous when used on the K-380. To
prevent serious injury, use only the accessories listed
below.
Cable Selection
Solid Core (Integral Wound) Cable
Model No.
Description
C-31 IW
3
/
" x 50' w/Solid Core Cable
8
C-32 IW
3
/
" x 75' w/Solid Core Cable
8
C-44 IW
1
/
" x 50' w/Solid Core Cable
2
C-45 IW
1
/
" x 75' w/Solid Core Cable
2
10
Additional Tools Available For
Cable
Catalog
Model
No.
No.
62990
T-201
62995
T-202
63000
T-203
54837
T-204
63005
T-205
63010
T-206
63020
T-208
63025
T-209
63030
T-210
63035
T-211
63040
T-212
63045
T-213
63050
T-214
63055
T-215
63060
T-216
63065
T-217
63280
T-218
63070
T-219
63080
T-220
63220
T-221
59982
59987
Maintenance Instructions
Make sure machine is unplugged from power
source before performing maintenance or making
any adjustment.
Lubrication
Grease all exposed, moving and rotating parts, such
as guide tube assembly, as required.
NOTE! No lubrication of the Motor Shaft is required.
Autofeed Assembly
Proper cleaning and lubrication of the autofeed assem-
bly is advised for long, trouble-free operation. After each
use, hose out autofeed assembly with water and lubricate
with lightweight machine oil.
Cables
Cables should be thoroughly flushed with water to pre-
vent damaging effects of sediment and drain cleaning
compounds. Periodically lubricate cables and couplings
with RIDGID Cable Rust Inhibitor. See accessories for
catalog number information.
When not in use, store cables indoors to prevent dete-
rioration by the elements.
Cables should be replaced when they become severely
corroded or worn. A worn cable can be identified when
outside coils of cable become flat.
Ridge Tool Company
3
/
" &
8
Description
Straight Auger, 5" (127mm) Long
Bulb Auger, 1
1
/
" O.D.
8
Bulb Auger,
7
/
" (22mm) Diameter
8
"C" Cutter, 1"
"C" Cutter, 1
3
/
"
8
Funnel Auger, 3" (76mm) Long
Spiral Cutter, 1
1
/
" (38mm) Diameter
2
Spiral Cutter, 2" (51mm) Diameter
Grease Cutter, 1" (25mm) Wide
Grease Cutter, 1
3
/
" (35mm) Wide
8
Grease Cutter, 1
3
/
" (44mm) Wide
4
Four-Bladed Cutter, 1" (25mm) Wide
Four-Bladed Cutter, 1
3
/
" (35mm) Wide
8
Four-Bladed Cutter, 1
3
/
" (44mm) Wide
4
Chain Knocker, 2" (51mm) Diameter
Drop Head Auger, 4" (102mm) Long
Flue Brush, 3" (76mm) Diameter
Flue Brush, 2
1
/
" (64mm) Diameter
2
Flue Brush, 2" (51mm) Diameter
Flue Brush, 1
1
/
" (38mm) Diameter
2
Cable Rust Inhibitor, 1 Quart
Cable Rust Inhibitor, 1 Gallon
WARNING
1
/
"
2
Capítulos
Tabla de contenido
