Seat Adjustment; Parking Brake Adjustment - MTD 760 Serie Manual De Operador

EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
12. On 46" decks, repeat steps 4 through 11 on the opposite
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
side of the cutting deck.
IMPORTANT:
System™ , return to the operator's position and engage the PTO.
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
Keep the cutting deck running for a minimum of two minutes,
allowing the underside of the cutting deck to thoroughly dry.
Adjustments
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
WARNING!
adjustments while the engine is running, except
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
where specified in the operator's manual.
Leveling the Deck
NOTE: Check the tractor's tire pressure before performing any
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
deck leveling adjustments. Refer to Tires in the Service section of
this manual for more information regarding tire pressure.
Front To Rear
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
The front of the cutting deck is supported by a stabilizer bar that
can be adjusted to level the deck from front to rear. The front of
the deck should be between ¼-inch and 3⁄8-inch lower than the
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
rear of the deck. Adjust if necessary as follows:
1. With the tractor parked on a firm, level surface, place the
lever for lifting the platform on the second to the top notch
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
(second highest position) and rotate the blade as close to
the discharge channel that is parallel to the tractor.
2. Measure the distance from the front of the blade tip to
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
the ground and the rear of the blade tip to the ground.
The first measurement taken should be between ¼" and
3⁄8" less than the second measurement. Determine the
approximate distance necessary for proper adjustment and
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
proceed, if necessary, to the next step.
3. On some models: Locate the jam nut and lock nut on
the front side of the stabilizer bracket. Others have just a
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
flange nut as seen in Figure 6-4.
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE
After loosening the jam nut (on some models):
• Tighten the lock nut to raise the front of the deck;
• Loosen the lock nut to lower the front of the deck.
EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.
PROPIEDAD EVANS.COM.MX PROPIEDAD EVANS.COM.MX PROPIE 22 S 6— M
ection
After cleaning your deck with the Deck Wash
Never attempt to make any
Figure 6-4
& a
aintenance djuStMentS
4. Retighten the jam nut loosened earlier when proper
adjustment is achieved.
Side to Side
If the cutting deck appears to be mowing unevenly, a side to side
adjustment can be performed. Adjust if necessary as follows:
1. With the tractor parked on a firm, level surface, place the
deck lift lever in the second from the top notch (second
highest position) and rotate both blades so that they are
perpendicular with the tractor.
2. Measure the distance from the outside of the left blade
tip to the ground and the distance from the outside of the
right blade tip to the ground. Both measurements taken
should be equal. If they're not, proceed to the next step.
3. Loosen, but do NOT remove, the hex cap screw on the left
deck hanger bracket. See Figure 6-5.
Figure 6-5
4. Balance the deck by using a wrench to turn the adjustment
gear (found immediately behind the hex cap screw just
loosened) clockwise/up or counterclockwise/down.
The deck is properly balanced when both blade tip
measurements taken earlier are equal.
5. Retighten the hex cap screw on the left deck hanger
bracket when proper adjustment is achieved.

Seat Adjustment

Refer to the Set-Up and Assembly section of this manual for seat
adjustment instructions.

Parking Brake Adjustment

WARNING!
Never attempt to adjust the brakes
while the engine is running. Always disengage PTO,
move shift lever into neutral position, stop engine
and remove key to prevent unintended starting.
If the tractor does not come to a complete stop when the brake
pedal is completely depressed, or if the tractor's rear wheels
can roll with the parking brake applied, the brake is in need of
adjustment. See an authorized MTD Service Dealer to have your
brakes properly adjusted.
Hex Cap Screw