HERKULES DS 405/1E Manual De Instrucciones página 13

Anleitung DS 405-1 E:Anleitung DS 405-1 E
3. A sound-absorbing foam rubber mat is not
supplied with the saw. It is strongly
recommended to use such a mat, however, in
order to minimize vibrations and noise.
Description:
Soft foam rubber mat: 450 x 250 x 13 mm
Do not overtighten the screws. Leave enough scope
for the foam rubber mat to develop a good absorbing
effect.
7. Assembly
Caution! Pull out the power plug before carrying out
any maintenance and conversion work on your
fretsaw.
7.1 Mounting the saw blade guard and the
sawdust blower facility (Fig. 4/5/10)
Put the retention bolt (23) on the radial arm (30).
Slide the saw blade guard (26) onto the retention
bolt (23).
Insert the screw (45) through the bore hole of the
retention bolt (23) and the saw blade guard (26).
Use the nut (46) to secure the screw from falling
out.
The saw blade guard can be fixed at various
heights with the clamping screw (47).
Align the tube (49) towards the saw blade in
order to blow the sawdust away from the kerf
when sawing.
The tube (49) can be fixed at various positions
with the screw (28).
To connect the saw to a vacuum cleaner, plug
the standard adapter tube on the chip extractor
unit (Fig. 10).
7.2 Changing the blade (Fig. 1/6)
Turn the tightening screw (39) counterclockwise
to remove the tension from the saw blade (41).
Unscrew the left cover (6).
First take the blade out of the top blade holder
(31), pressing down the upper pendulum arm as
you do so.
Then take the blade out of the bottom blade
holder (18).
Pull the blade up and out through the table insert
(15).
Install the new blade in reverse order.
Caution: Always insert the blade so that the teeth
point toward the saw table.
07.12.2010
The blade can be inserted in slot a or b;
Slot a: For cuts along the axis of the radial arm.
Slot b: For cuts across the axis of the radial arm.
Tension the blade by turning the clamping screw
(39) anticlockwise (right-hand thread).
7.3 Tilting the saw table (Fig. 7)
Undo the locking screw (12).
Tilt the table (14) to the left until the indicator (11)
points to the required angle value on the scale
(13).
Important: For precision work you should first
carry out a trial cut and then re-adjust the tilt
angle as required.
8. Operation
8.1 Please note:
Your saw does not cut wood automatically. For
cutting to occur, you have to guide the wood
against the blade.
The teeth cut only on the down stroke of the
blade.
You have to guide the wood slowly against the
blade because the teeth are very small.
Every new user needs a certain training period.
You are certain to break a number of blades at
the beginning.
When cutting thick timber, be particularly careful
not to bend or twist the blade. This will help to
prolong blade life.
8.2 On/Off switch (2; Fig. 2)
Press the green button to switch the saw on.
Press the red button to switch the machine off.
Please note: The machine is equipped with a
safety switch to prevent it being switched on
again accidentally after a power failure.
8.3. Blade speed regulator (3)
The blade speed regulator allows you to set the
blade speed appropriate to the material to be cut.
8.4 Carrying out internal cuts
1. A feature of this fretsaw is that it allows you to
carry out internal cuts in a panel without
damaging it on the outside or circumference.
WARNING: TO PREVENT INJURIES DUE TO THE
SAW STARTING UP ACCIDENTALLY, ALWAYS
SET THE SWITCH TO „0" POSITION AND PULL
THE POWER PLUG OUT OF THE SOCKET-
9:26 Uhr Seite 13
GB
13