Protecting The Environment - DeWalt DW714 Manual De Instrucciones

Fig. KK
Dust Extraction (Fig. A, C)
• Fit the dustbag 32 onto the dust spout

WARNING: Whenever possible, connect a dust
extraction device designed in accordance with the
relevant regulations regarding dust emission.
Connect a dust collection device designed in accordance
with the relevant regulations. The air velocity of externally
connected systems shall be 20 m/s ±2 m/s. Velocity
to be measured in the connection tube at the point of
connection, with the tool connected but not running.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from
the power source before attempting to move it,
change accessories or make any adjustments.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
DO NOT use lubricants or cleaners (particularly spray
or aerosol) in the vicinity of the plastic guard. The
polycarbonate material used in the guard is subject to
attack by certain chemicals.
1. All bearings are sealed. They are lubricated for life and
need no further maintenance.
2. Periodically clean all dust and wood chips from around
AND UNDER the base and the rotary table. Even though
slots are provided to allow debris to pass through, some
dust will accumulate.
3. The brushes are designed to give you several years of
use. To replace the brushes refer to Brushes or return
the tool to the nearest service center for repair. A list of
service center locations is packed with your tool.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Repairs

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D
or a D
identical replacement parts.

Protecting the Environment

14 .
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions.
Capacity of cut
47° miter left , 52° right
45° bevel left, 0° right
0 degree miter, 0 degree bevel
Max. Height 3.5" (89 mm)
Max. Width 5.1" (130 mm)
45 degree miter, 0 degree bevel
Max. Height 3.5" (89 mm)
Max. Width 3.6" (91 mm)
0 degree miter, 45 degree bevel
Max. Height 2.0" (50 mm)
Max. Width 5.1" (130 mm)
45 degree miter 45 degree bevel
Max. Height 1.8" (45 mm)
Max. Width 3.6" (91 mm)
Power
Revolutions per minute
Automatic electric brake
DW714-AR
220V
~50Hz
WALT factory service center
e
WALT authorized service center. Always use
e
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Specifications
Result Width 3.7" (95 mm)
Result Height 2.7" (68 mm)
Result Width 2.6" (67 mm)
Result Height 2.7" (68 mm)
Result Width 3.7" (95 mm)
Result Height 1.6" (40 mm)
Result Width 2.8" (70 mm)
Result Height 1.6" (40 mm)
DW714-B2 DW714-B3 DW714-BR
220V 120V 127V
~50–60Hz ~50– ~60Hz
60Hz
ENGlIsH
1650 W
4600 RPM
Yes
DW714-B2C
220V
~50Hz
59