Tabla de contenido
Idiomas disponibles
Idiomas disponibles
WARNING: with dip 7 ON the input OPEN / CLOSE (terminals 11-12) switches OPEN, the
PEDESTRIAN input (terminals 11-13) switches CLOSE.
In MAN mode, it is not necessary to run the race setup, and the dip-switches 1, 2, 3 and
4 are not used.
8
2nd RADIO CH
OPENING
9
RAM BLOW
SENSITIVE EDGE
10
SELECTION
JUMPER J1
Bridged=
following the connection of the external photocell contact (input 17 - 18), the gate
closes automatically after 5 seconds.
Not bridged=
function disconnected.
IMPORTANT:
Each pair of terminals attached to an NC contact that is not in use must be short-circuited in order to
ensure the proper operation of the board.
The door's earthing system must comply with current standards. The manufacturer will accept no li-
ability for any damage deriving from failure to comply with this requirement.
8. 433.92 MHz BUILT-IN RADIO RECEIVER
The radio receiver can learn up to a maximum of 30 rolling codes (BUG2R, BUG4R, K-SLIM-RP, T-4RP)
which can be set on the two channels as required.
The first channel directly commands the control board for opening the automatic device; the second
channel commands a relay for a N.O. no-voltage output contact (terminals 21 and 22, max. 24 Vac, 1 A).
LEARNING SYSTEM FOR RADIO CONTROL DEVICES
P1 = OPEN/CLOSE
1_ press button P1 briefly to associate a radio control device with the OPEN/CLOSE function;
2_ LED DL7 turns off to indicate that the code learning mode has been activated (if no code is entered within
10 seconds, the board exits the programming mode);
3_ press the button of the relative radio control device;
4_ LED DL7 turns on again to indicate that the code has been memorised (if this does not happen, wait 10
seconds and start again from point 1);
5_ to memorise codes to other radio control devices, repeat the procedure from point 1 up to a maximum
of 30 transmitters;
6_ to memorise codes on the 2nd channel, repeat the procedure from point 1 using button P2 instead of P1;
7_ to exit the learning mode without memorising a code, press button P1 or P2 briefly.
Notice:
if the maximum number of radio control devices (30) is exceeded, LED DL7 flashes rapidly
for about 3 seconds without memorising the code.
REMOTE PROGRAMMING BY MEANS OF T-4RP and K-SLIM-RP (V 4.X)
With the new version of software V 4.X it is possible to carry out the remote self-learning of the new
version of transmitters T-4RP and K-SLIM-RP (V 4.X), that is without pressing the receiver's program-
ming buttons.
It will be sufficient to have an already programmed transmitter in the receiver in order to start the
procedure of remote programming of the new transmitters. Follow the procedure written on the in-
structions of the transmitter T-4RP and K-SLIM-RP (V 4.X).
CANCELLING CODES FROM RADIO CONTROL DEVICES
Bistable function active: To the impulse of transmitter the contact is acti-
On
vated and remains activated until the next pressure.
Monostable function 2 sec active: To the impulse of transmitter the contact
Off
is activated and remains activated for 2 sec.
the "opening ram blow" function is on. This permits the release of the
On
electric lock (to be used only in the presence of an electric lock);
Off
the "opening ram blow" function is off;
On
RESISTIVE SENSITIVE EDGE (terminal no. 15)
RESISTIVE EDGE - potential free contact N.C. (terminal no. 15)
Off
Note: if not used, keep the DIP in the OFF position.
P2 = 2nd channel
17
Tabla de contenido
