Disposal; Spare Parts - E-Tech EG Instrucciones De Uso

8.4. Mechanical seal inspection
If the mechanical seal (36.00) and the oil chamber
are to be inspected, follow these instructions.
GB
CAUTION: there may be slight pressure in
the oil chamber.
Care must be taken to avoid a sudden spur-
ting of oil.
Once the plug (34.08) with washer have been remo-
ved, adjust the hole to the downward position and
empty the chamber completely.
Do not dispose of the waste oil in the enviroment.
The mechanical seal (36.00) can be inspected by
removing the screws (34.12).
When re-filling with fresh oil, remember that the
chamber must not be completely filled; a sufficient
quantity of air must remain inside it in order to
compensate for overpressure caused by thermic
dilation of the oil.
The quantity of oil to be inserted in the chamber is:
0,08 litres
Use white oil suitable for food machinery and
pharmaceutic use.

9. DISPOSAL

The final disposal of the device must be done by spe-
cialized company.
Make sure the specialized company follows the clas-
sification of the material parts for the separation.
Observe the local regulations and dispose the device
accordingly with the international rules for environ-
ment protection.

10 SPARE PARTS

10.1 Spare-parts request
When ordering spare parts, please quote their desi-
gnation, position number in the cross section drawing
and rated data from the pump name plate (type, date
and serial number).
Any pumps that require inspection/repair
must be drained and carefully cleaned inside
and outside before dispatch/submission.
Hose down all accessible parts with a jet of water.
The spare parts request shall be sent to Franklin
Electric S.r.l by phone, fax, e-mail.
Nr. Designation
12.00 Casing cover
12.20 Screw
12.21 Nut
14.00 Pump casing
14.20 Casing gasket
14.22 Fastening ring
14.24 Screw
14.46 Plug
14.47 Gasket
14.80 Air release plug
15.50 Strainer
15.70 Screw
Page 14 / 80
28.00 Impeller
28.04 Impeller nut
28.08 Washer
28.20 Impeller key
34.03 Oil chamber cover
34.04 Wear ring
34.05 Nut
34.08 Plug
34.09 O-ring for plug
34.12 Screw
34.13 O-ring
36.00 Mechanical seal
40.00 Radial shaft seal
64.08 Shaft sleeve
64.12 O-ring
70.00 Motor cover, pump side
70.05 O-ring
70.08 O-ring
70.09 O-ring
70.10 O-ring
70.11 Cable gland ring (float switch)
70.12 Cable gland ring
70.13 Washer
70.16 Cable gland
70.17 Lock ring
70.20 Screw
70.23 O-ring
73.00 Pump side bearing
73.08 V-Ring
76.00 Motor casing with winding
76.01 Motor jacket with winding (1)
76.02 Kit, motor jacket
76.04 Cable gland
76.60 Float switch
76.62 Jacket cover
76.63 Screw
76.64 Handle
76.65 Handle clamp
76.66 Washer
78.00 Shaft with rotor packet
78.12 O-ring
81.00 Bearing
82.01 Motor end-shield, non-drive end (1)
82.02 Screw
82.03 O-ring
82.04 Compensating spring
82.05 Screw (1)
82.30 Plug
94.00 Capacitor
94.02 Cable with plug
94.04 Capacitor collar
96.00 Cable
96.07 Cable fastener
96.08 Clamp
96.09 Screw
96.10 Nut
96.12 Cable fastener
96.13 Cable fastener
(1) Cannot be supplied separately (2) Oil
(3) Grease
ED, EG Rev. 3 - Operating Instructions