Technical Assistance; Technical Description; Technical Features; Technical Data - E-Tech EG Instrucciones De Uso

- In case of changes or variations made without
authorization of the manufacturer.
- In case of technical interventions executed by a
GB
non-authorized personnel.
- In case of failing to carry out adequate maintenance.

1.5 Technical assistance

Any further information about the documentation,
technical assistance and spare parts, shall be reque-
sted from: Franklin Electric S.r.l.

2 TECHNICAL DESCRIPTION

See designation on the pump name-plate or on the
bar-code label.
Meaning of the designations:
ED = Stainless steel pump.
V = With free-flow (vortex) impeller.
T = With
indication = with single-phase motor).
EG = Cast iron and Stainless steel pump.
N = With open impeller
T,F = With free-flow (vortex) impeller.
T = With
indication = with single-phase motor).

2.1 Intended use

Standard construction
- For clean or slightly dirty water, with solids in
suspension up to 10 mm grain size. for EGN.
- For clean and dirty water, also containing solids
with maximum size:
35 mm for ED, EDV;
50 mm for EGT, EGF;
With a high solid content or with filamentous par
ticles use only the free-flow (vortex) EDV, EGT,
EGF. construction.
- Maximum liquid temperature: 35 °C.
- Maximum liquid density: 1100 kg/m
- Minimum dimensions
0.55x0.55m; depth 0.5 m.
- Minimum immersion depth see also sections 6.5.,
6.6.
- Maximum submersion depth 5 m.
For outdoor use the power supply cable must have
a length of not less than 10 m.

2.2 Improper use

The device is designed and built only for the purpose
described in paragraph 2.1.
Do not use in garden ponds, tanks or
swimming pools when people are in the
water.
The Pump cannot be used in explosive or
flammable environments.
Improper use of the device is forbidden, as is
use under conditions other than those
indicated in these instructions.
Improper use of the product reduces the safety and
the efficiency of the device, Franklin Electric S.r.l shall
not be responsible for failure or accident due to impro-
per use.
Page 10 / 80
three-phase motor (without
three-phase motor (without
3 .
of installation
2.3 Marking
The following picture is a copy of the name-plate that
is on the external case of the pump.
1 Pump type
2 Delivery
3 Head
4 Rated power
5 Tension nominale
6 Nom. motor current
7 Capacitor
8 Fréquence
10 Insulation class
14 Protection
15 Serial number
16 Certifications

3 TECHNICAL FEATURES

3.1 Technical data

Dimensions and weight (paragraph 12.1).
Nominal speed 2900/3450 rpm
Protection IP X8
Supply voltage / Frequency:
- up to 240V 1~ 50/60 Hz
- up to 480V 3~ 50/60 Hz
Check that the mains frequency and voltage corre-
spond to the electrical characteristics shown on the
indicator plate.
Sound pressure at minimum immersion depth: < 70
dB (A).
Noise disappears when the pump is submersed.
Maximum starts/hour: 30 at regular intervals.

4 SAFETY

4.1 General provisions
Before using the product it is necessary to
know all the safety indications.
Carefully read all operating instructions and
the indications defined for the different steps:
from transportation to disposal.
The specialized technicians must carefully
comply with all applicable standards and laws,
pit:
including local regulations of the country
where the pump is sold.
The device has been built in conformity with
the current safety laws. The improper use
could damage people, animals and objects.
The manufacturer declines any liability in the
event of damage due to improper use or use
under conditions other than those indicated on
the name-plate and in these instructions.
i
Follow the routine maintenance schedules
and the promptly replace damaged parts, this
will allows the device to work in the best
conditions.
Use only original spare parts provided from
Franklin Electric S.r.l or from an authorized
distributor.
Don't remove or change the labels placed on
the device.
Do not start the device in case of defects or
damaged parts.
Maintenance operations, requiring full or
partial disassembly of the device, must be
done only after disconnection from the supply.
Pollution of the liquid could occur due to
leakage of lubricants.
ED, EG Rev. 3 - Operating Instructions
1
Pump XXXXX
N° XXXXXXX
2
Q
XX-XX l/min H XX-XX m
3
H min XX m H max XX m
8
Motor ~
X XX Hz P1 XX kW
5
XXXXX V XX A Tmax °C
Continuos Duty Cl XX IP 68 Capacitor XX uF XX V
7 10 14
16
Made in Italy
15
3
3
4
6