Idiomas disponibles
Idiomas disponibles
m WARNING! If there are leaks in the water sys-
tem, switch off the product immediately with the
On/Off switch (5) and disconnect the product from
the mains with the mains connection cable. There
is a risk of electric shock! Start connecting the wa-
ter connections again.
NOTE: Do not operate the product with a closed water
tap. Running dry will damage the product.
1.
Ensure that the high-pressure cleaner is switched
off at the On/Off switch (5).
2.
Plug the mains plug into the socket.
3.
Open the water tap fully.
4.
Switch the product on with the On/Off switch (5).
Always switch on the product only after you have
connected all the water lines and they are leak-
tight. The motor switches on until the necessary
pressure is built up. After pressure build-up, the
motor switches off.
5.
Unlock the trigger (22) with the unlocking button
(21).
6.
Press the trigger (22) on the spray gun (9). The
product motor starts automatically.
7.
By releasing the trigger (22), the product switches
off, the high pressure in the system is maintained.
11.2 Using the hose reel (17)
Unrolling: Loosen the fastening clip (4) and pull the
required length of high-pressure hose (3) off the hose
reel (17). It is not necessary to unwind the high-pres-
sure hose (3) completely.
Rolling up: Roll up the high-pressure hose (3) using
the hose reel winding button (12). Fasten the end of the
high-pressure hose (3) with the fastening clip (4).
11.3 Use of cleaning agents
NOTE: Use only cleaning agents that are suitable for
use in high-pressure cleaners.
1.
To fill the cleaning agent tank (14), pull it out of the
holder on the high-pressure cleaner.
2.
Remove the sealing cap with suction hose (15)
from the cleaning agent tank (14).
3.
Fill the cleaning agent tank (14) with suitable
cleaning agent.
4.
Fit the cap with suction hose (15) and put the
cleaning agent tank (14) back into the holder on
the high-pressure cleaner.
5.
Use the variable nozzle (6) in low pressure mode
or the rotating brush (10). The cleaning agent is
drawn in automatically.
11.4 Stop operation
1.
After working with cleaning agents, rinse the sys-
tem with clean water. To do this, remove the clean-
ing agent tank (14).
2.
Switch the product off with the On/Off switch (5).
Pull out the mains plug.
3.
Turn off the water tap.
4.
Disconnect the high-pressure cleaner from the
water supply.
5.
Press the trigger (22) of the spray gun (9) to re-
lease the existing pressure in the system.
11.5 Self-priming function
You can also use the product independently of the
water supply (e.g. rain barrel) thanks to the integrated
water suction function. This function can only be used
with a suction hose with filter basket (not included in the
scope of delivery).
m WARNING! The product itself must not be immersed
in the open water source. There is a risk of persons be-
ing injured due to electric shock.
1.
Plug the suction hose with filter basket onto the
water connection coupling (25).
2.
Hang the end with the filter basket into the water
extraction point. Make sure you have a sufficient
water supply and a safe water supply.
NOTE: Running dry will damage the product.
3.
Remove the lance (2) from the spray gun (9). Press
the trigger (22) of the spray gun (9) and only then
switch on the product.
4.
The product starts to draw in water and the air can
escape.
5.
When there is no more air in the product, you can
release the trigger (22) of the spray gun (9). You
can connect the attachment of your choice to the
spray gun (9).
NOTE: The product should not be higher than the
water take-off point.
12. Transport (Fig. 1)
With the U-shaped handle (1) extended, you can trans-
port the product comfortably.
1.
Pull out the U-shaped handle: Press the release
button for the U-shaped handle (11) and pull the
handle (1) upwards.
2.
Push in the U-shaped handle: Press the release
button for the U-shaped handle (11) and push the
handle (1) downwards.
www.scheppach.com
GB | 25
