Idiomas disponibles
Idiomas disponibles
4. WARNINGS AND SAFETY NOTES
Failure to observe the following information may result in personal
injury or material damage.
WARNING
Keep packaging material away from children. There is a risk of
su ocation.
Electric shock
WARNING
As with every electrical device, use this massager carefully and
cautiously, in order to avoid hazards due to electric shock.
Therefore, observe the following instructions for use:
• Only use this device with the voltage specified on the device,
• Never use the device if it or its accessories show visible signs
of damage,
• Do not use the device during a storm.
In the event of defects or operational faults, switch the device o
immediately and disconnect it from the mains socket. Do not pull
on the mains cable or on the device to disconnect the plug from
the socket. Never hold or carry the device by the mains cable.
Keep the cables away from hot surfaces. Do not crush, bend or
twist the cables. Do not insert needles or any sharp objects.
Ensure that the massager, the switch and the mains cable do not
come into contact with water, steam or other liquids.
Therefore, only use the device
• in dry interior rooms (e.g. never in the bath or sauna),
• with dry hands.
Never pick up a device that has fallen into water. Disconnect the
mains plug immediately. Do not use the device if it or its acces-
sories are visibly damaged. Do not drop the device or subject it
to any impacts.
Repairs
WARNING
• Only specialist personnel may perform repairs on electrical
devices. Improper repairs may put users in significant danger.
For repairs, please contact Customer Services or an author-
ised retailer.
• The zip fastening on the back of the Shiatsu massager must
not be opened. It is only used for technical production rea-
sons.
Risk of fire
WARNING
There may be a risk of fire if the device is used improperly or these
instructions for use are ignored.
The massager must therefore be operated as follows:
• Never operate the massager underneath a cover, such as a
blanket, pillow, etc.
• Never use the device near petrol or other highly flammable
substances.
Handling
NOTICE
The device must be switched o and disconnected after every use
and before cleaning.
• Operate the device only in an upright position, and never
place it flat on the ground.
• Do not place your full weight (sitting, lying down, or standing)
on the moving parts of the device or place any objects on
the device.
• Do not expose the device to high temperatures.
5. DEVICE DESCRIPTION
The associated drawings are shown on page 4.
Shiatsu seat cover
1
Neck section with removable cover
2
4D massage heads in the neck section
3
PRESS button (for releasing the neck section)
4
Massage heads for the back area
5
Back section
6
Seating surface with removable cover
7
Buttonhole
8
Hand switch
9
Storage bag
10
Mains plug
Hand switch
11
NECK button (massage of the neck area)
UPPER BACK button
12
(massage of the upper back)
LOWER BACK button
13
(massage of the lower back)
14
SPOT button
(targeted massage of a spot on the back)
15
Arrow buttons
(to set the SPOT massage position higher or lower)
16
High massage intensity
17
Low massage intensity
18
ON/OFF button
6. USAGE
6.1 Positioning the Shiatsu seat cover
1. Position the Shiatsu seat cover upright on a suitable seat with
a seating surface and back rest (chair, sofa or similar). Make
sure that the entire surface of the seating surface
back area
are in contact with the seat.
5
2. Ensure that the mains cable does not pose a trip hazard. Insert
9
the mains plug
6.2 Adjusting the neck section
Start by adjusting the neck section
as required. Both the height and the angle can be adjusted. Al-
ways make sure that the 4D massage heads
so that they massage your neck comfortably and are not directed
at your head.
1. Adjusting the height: (The corresponding drawing A is shown
on page 5.) Reach with one hand under the centre of the neck
section
1
. With the other hand, press the PRESS button
the top of the rear of the back section. This releases the locking
mechanism and you can then move the neck section
desired height. Then release the PRESS button
14
into a suitable socket.
1
of the Shiatsu seat cover
2
6
and the
are positioned
3
at
1
to the
3
and allow
