YATO YT-86200 Manual De Instrucciones página 9

Do not spray any materials that may cause an unknown hazard.
Caution! A high-pressure jet can cause severe skin damage. Never
allow any part of the body to come into contact with the jet.
Protective clothing does not provide suffi cient protection against in-
juries in the form of injections.
In case of injection of high-pressure jet under the skin, immediately
consult a physician. Inform the physician about the substance in-
jected.
Do not eat, drink or smoke in the working area.
Always wear a respiratory protective mask to protect against harmful
vapours.
Ensure adequate ventilation so that there is no accumulation of fl am-
mable vapours in the air of the working space.
Appropriate measures should be taken to prevent hazards caused
by the substance being sprayed. Follow the instructions given on the
packaging or by the manufacturer of the substance to be sprayed.
Do not spray the substances listed as prohibited in this manual.
Do not spray materials of unknown composition.
Do not use the device without the nozzle cover installed.
Never use the device if any protecting elements or covers have been
damaged.
Only use original spare parts and carry out any repairs at an author-
ised workshop.
Disconnect the unit from the mains before performing any servicing
works and when it is not used.
Always check that the actual supply voltage corresponds to the volt-
age indicated on the unit's nameplate.
PREPARING FOR OPERATION
CAUTION! Only install the accessories when the supply voltage is
disconnected. Make sure that the power switch is in the off position.
Spraying liquids
The gun is used to spray water. You can dissolve the plant fertiliser in
water, but it must dissolve completely and not create a slurry. It is for-
bidden to spray fl ammable substances, paints, solvents, corrosive
substances, or alcohol even if diluted in water. Gun materials and
seals are not suitable for working with substances other than water.
Spraying other substances may result in damage to the device.
Filling the tank
Unscrew the tank from the gun (II), and fi ll it with water. Leave ap-
proximately 0.5 cm of free space, measuring from the top of the tank.
Slide the fi lter with the hose into the tank, and then carefully screw
the tank to the gun to avoid spilling the contents. Tighten the tank
with such force to seal the connection.
Charging the storage battery
After pressing the power switch, the status lights of the storage bat-
O R I G I N A L
GB
tery located on the upper gun wall (III) should light up. The more
status lights are on, the higher the storage battery charge level. If
the storage battery needs charging, connect the supplied cable to
the socket under the cap on the back gun wall (IV).
Insert the second plug of the cable into the USB socket. You can use
a socket in your computer case or an AC power adapter equipped
with a socket for this purpose.
During charging, the status lights will light up successively. The end
of charging is indicated by all the status lights illuminating. As soon
as charging is complete, disconnect the device from the charger and
secure the socket with the cap. Leaving the device connected to the
charger for an extended period after the storage battery has been
charged may lead to damage to the storage battery.
Safety instructions for battery charging
Caution! Before starting charging, make sure that the charger body,
cord and plug are not cracked or damaged. It is forbidden to use
a defective or damaged charger! Use only the supplied accessory
charger to charge the batteries. Use of another charger may result in
fi re or damage to the device. The battery should only be charged in a
closed, dry room, protected against unauthorised access, especially
by children. Do not use the charger without the constant supervision
of an adult! If you need to leave the room where the vacuum clean-
er is being charged, disconnect the charger from the mains by re-
moving the charger plug from the socket. If smoke, odours, etc. are
escaping from the charger, remove the charger plug from the socket
immediately! The product is supplied with an uncharged battery and
should therefore be charged according to the procedure described in
the manual before use. Li-ion (lithium-ion) batteries do not have the
so-called "memory eff ect", which allows them to be recharged at any
time. However, it is recommended to discharge the battery during
normal operation and then charge it to full capacity. If, due to the
nature of work, it is not possible to use the battery in such a manner
every time, it should be done at least every several work cycles.
Never discharge the batteries by closing the battery contacts, as this
will cause irreparable damage! Also, do not check the battery charge
status by closing the contacts and checking sparking.
Battery storage
If possible, it is recommended to disconnect the battery from the
product for storage. Proper storage conditions will help to extend
the life of the battery. The battery lasts for about 500 charge-dis-
charge cycles. Store the battery in a temperature range from 0 to 30
degrees Celsius at a relative humidity of 50%. To store the battery
for a longer period of time, it should be charged to approx. 70%
of its capacity. In case of prolonged storage, the battery should be
periodically charged once a year. Do not over-discharge the bat-
tery as this will shorten its life and may cause irreparable damage.
During storage, the battery will gradually discharge due to leakage.
The self-discharge process depends on the storage temperature,
I N S T R U C T I O N S
9