Diamond BUFFET 4-6 STOCK Manual Del Usuario página 4

Operator's guide:
1)Unpacking instructions
2)Internal glass support shelves
3)The sliding doors
I
4)Cleaning the internal tank
5)External cleaning
UK
6)Basin support spacers
7)Table
D
8)Connection to the mains
9)Controls
E
F
WARNINGS
!
NL
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety.
P
1. Adults should operate this appliance only. Do not allow children to use the controls or play with it. 2
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
S
installation of the appliance should be carried out by a qualified electrician or other competent person.
4 . Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
DK malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs. 6
7 . The manufacturers of this appliance accept no responsibility for the consequences of misuse in
FIN
contravention of these safety instructions. It further reserves the right to carry out improvements without
prior notice. 8
B
near sources of heat, such as radiators, stoves, etc.
for at least 30 cm.
GR
edges. 12 . If damp air or products to be refrigerated should cause ice to form on the evaporator, we
recommend stopping the compressor and placing the goods in special refrigerated containers, kept at the
CZ
same temperature, until defrosting is completed;if this is not carried out the compressor will continue to
operate leading to a wasteful consumption of electricity and poor performance.
EE
working and unused, it is indispensable to keep the door open at least 10 cm.
LV
!
Our products are for internal use only do not install outside restaurants, shops.
LT
1. UNPACKING INSTRUCTIONS
H
CARDBOARD BOX 1a.
WOODEN CRATE 1b.
M
and curved panes out of the tank. . Insert forks of forklift truck between the appliance and pallet or crate.
4. Lift the cabinet.
PL
7. Insert the two spacers in the holes on the back of the cabinet
by engaging the wheel brakes. . Make sure there is nothing left in the package before disposing of it.
10. Sort out the packaging materials in order to facilitate disposal (see fig. 1).
SK
2. INTERNAL GLASS SUPPORT SHELVES
The appliance is provided with 3 glass shelves, placed inside the tank.
SLO
packaging. 2.
the rear internal wall. . Rest the shelves on the brackets, making sure they stick to the suckers (see
picture 2)
3. THE SLIDING DOORS
Each sliding door has a snap closure that is automatically triggered when the door is shut.
1.
the door, pull the mobile part of the handle downwards (see picture 3).
4. CLEANING THE INTERNAL TANK
1. Remove the protective film from the bottom and sides.
detergents. . Remove the plug from the drainage hole in the tank to drain off the defrosting water. 3
N.B . The plug may be kept in position if the cabinet is used on a daily intermittent basis, and must be
removed when the cabinet is switched off at the end of the day (see figure 4).
5. EXTERNAL CLEANING
1. Refrain from using abrasive products or wipers.
cleaning products generally available on the market to clean the wooden surfaces, which should anyway
be water-based emulsions, free of all solvents.
6. BASIN SUPPORT SPACERS
1. Remove the protective film from the spacers.
the tank. . Place the shorter spacers in the slots on the long spacers. Different compositions can be 3
made according to the size and position of the basins.
5. For the pastry models, mount only the stainless steel pastry tray, resting it on the sides (see figure 5).
5
. Avoid installing the cabinet directly in line with sunlight. . Nevere install the appliance
11 . Ensure that the products displayed on the shelves and grills do not hang over the
Cut surrounding tape. Remove the cardboard package by sliding it upwards.
Remove the nails from the wooden crate with care. . Take the crystal shelves
3
5. Remove the pallet or crate. . Place the appliance on a flat and level surface.
9
Mount the suckers onto the brackets.
4
Operator's guide
10)Checking correct operation
11)Replacing the lamps
Maintenance manual (Page 48):
1)Cleaning the condenser
2)Internal cleaning and evaporator cleaning
3)Wiring diagram diagram of refrigeration unit
10 . Keep the ventilation grills free from obstruction
6
. 8
3. Mount the slot-in brackets in the square holes on
2. Clean the tank with a soft sponge and neutral
2. Use only a soft damp sponge.
4. Dry with a clean cloth.
2. Place the longer spacers in the slots on the sides of
4. Finally put the basins on the spacers as desired.
6
3
9
13 . If the appliance is not
2
. The appliance can be locked in place
1. Remove the shelves from the
3. Use specific
. It
To open
2.