Idiomas disponibles
Idiomas disponibles
5.4.2 Localization of the charging station
When the rechargeable battery is almost empty,
the robot lawn mower returns to the charging
station (19) by following the perimeter wire (18) in
a counterclockwise direction until it reaches the
charging station (19). Make sure, therefore, that
the charging station (19) faces in the right direc-
tion when you position it (Fig. 5b).
5.4.3 Connecting the charging station to the
power supply unit
1. Before you connect the charging station (19)
to the power supply, check that the mains po-
wer supply is 100-240 V at 50/60 Hz.
2. Connect the power supply unit (13) directly to
a socket outlet. Do not use the cable for any
other use.
3. Do not use the power supply unit if it is da-
maged (13). In the event of any damage to
cables or the power supply unit (13), contact
an authorized professional immediately for
replacement.
4. Do not charge up the robot lawn mower in a
damp location. Do not charge up the robot
lawn mower at temperatures above 40°C or
below 5°C.
5. Keep the robot lawn mower and the power
supply unit (13) away from water, sources of
heat and chemicals. Keep the cable of the po-
wer supply unit (13) away from sharp edges
in order to prevent damage.
6. Connect the power supply unit (13) to the
charging station (19)(Fig. 5c).
To charge up the rechargeable battery for the
robot lawn mower straight away while you are
still doing the installation work, fi rst switch on the
robot lawn mower with the main switch (7) and
place the robot lawn mower in the charging stati-
on (19).
5.4.4 Information about charging
The robot lawn mower returns to the charging sta-
tion (19) in each of the following situations:
•
You send the robot lawn mower back manu-
ally.
•
The battery charge level drops below 30%.
•
The end of the daily work time has been
reached.
•
The rain sensor has tripped.
•
The robot lawn mower has become overhea-
ted.
In these cases the robot lawn mower automa-
tically runs along the perimeter wire (18) until it
reaches the charging station (19).
Anl_FREELEXO_LCD_BT_SPK13.indb 35
Anl_FREELEXO_LCD_BT_SPK13.indb 35
GB
When the robot lawn mower wants to return to the
charging station (19), it will fi rst look for the peri-
meter wire (18) and then move along the perime-
ter wire (18) in counter-clockwise direction.
The LED indicator (21) on the charging station
(19) lights up red while charging of the rechargea-
ble battery is in progress.
When the LED indicator (21) on the charging
station (19) turns to green, this indicates that the
rechargeable battery is fully charged. Once it has
been fully charged, the robot lawn mower resu-
mes operation or remains in the charging station
until the next work time window (19).
If there is an obstacle on the perimeter wire (18)
during the trip back to the charging station (19),
the robot lawn mower will come to a stop in front
of the obstacle after several attempts and will not
be able to get back to the charging station (19).
Remove all obstacles on the perimeter wire (18).
If the temperature of the rechargeable battery ex-
ceeds 45°C, charging will stop in order to prevent
damage to the rechargeable battery. Charging
resumes automatically once the temperature has
dropped again.
If the temperature of the controller of the robot
lawn mower exceeds 75°C, the robot lawn mower
will return to the charging station (19). Operation
resumes in accordance with the settings once the
temperature has dropped again.
If the rechargeable battery becomes empty befo-
re the robot lawn mower has returned to the char-
ging station (19), it will not be possible for the ro-
bot lawn mower to start up again. Bring the robot
lawn mower back to the charging station (19) and
leave the main switch (7) switched on. The robot
lawn mower will be charged up automatically.
5.5 Perimeter wire
IMPORTANT! Severed perimeter wires and
consequential damages are not covered by
the warranty!
5.5.1 Laying the perimeter wire
The perimeter wire (18) can be laid both on the
ground and in the ground. The fastening pegs
(14) can break when hammered in if the ground
is hard or dry. Water the lawn before installing the
perimeter wire if the ground is very dry.
•
Installation on the ground
Lay the perimeter wire (18) securely on the
ground and fasten it with the supplied faste-
ning pegs (14) if you do not intend to scarify
or aerate the lawn any time later. You can still
adjust the position of the perimeter wire again
- 35 -
16.11.2023 10:09:17
16.11.2023 10:09:17
