Idiomas disponibles
Idiomas disponibles
Options – Footplate
Footrest
(7.21.3)
The footrests can be flipped up to
make it easier to get into and out
of the chair. By loosening the
screw (1) the angle can be ad-
justed in the area of ± 15°. Then
re-tighten the screw (see Torque).
Lower leg length
By loosening the screw (1) the
lower leg length can be adjusted.
Loosen the screws and adjust the
tube with the footrest to the desi-
red position. Then re-tighten the
screw (see page on Torque). Make
sure that the gap to floor is not
below the minimum of 2.5 cm.
Legrests and Latch
(7.23.1)
The legrest can be swung in and
outwards.
Fit your legrest by inserting it with
the footplate(s) pointing toward the
outside. Then rotate it toward the
inside until it locks into place (1).
To remove the legrest, depress the
lever (2), swing the footrest towards
the outside and lift to remove it.
Make sure that the legrest is pro-
perly locked into place.
CAUTION:
The legrests should not be used to lift or to carry
the wheelchair.
Elevating legrest
(7.24.1)
To elevate:
Lift your lower leg and press the release button. Pull
the legrest upwards and adjust it
to the desired height. As soon as
you release the button, the legrest
will click back into place.
To lower:
Lift your lower leg and press the
release button to unlock the
legrest to lower it (1). As soon as
you release the button, the legrest
will click back into place.
CAUTION:
The elevating legrest is not
allowed to be adjusted into the
lowest position to avoid any interference with
the castors.
CAUTION:
Keep hands clear of the adjustment mechanism
between the frame and the movable parts of the
legrest while elevating or lowering the legrest.
CAUTION:
Legrests are not to be used for lifting or carrying
the wheelchair with an occupant.
1
405
1
406 a
2
1
407 a
1
416.3
Options – Castor
Adjustment of seat height and seat angle
(7.51.1.3)
By loosening the screws (1, 2) you can adjust
the appropriate chair angle.
Adjust the castor so that, as far as possible,
the axle is at 90° to the floor. After adjustment,
all the screws must be re-tightened (see the
page on Torque).
The front seat height can also be adjusted by
altering the castor in the castor fork (Seat
heights 47, 50, 52 cm) and by altering the
castor connector (Seat height 42, 45 cm).
For detailed adjustability possibilites, please
see figure 1 and figure 2 on page 10.
Options – Axle Plates
Horizontal Axle
Position(7.51.1.2)
The axle plate can be positioned
forward for maximum maneuver-
ability or rearward for increased
stability.
CAUTION:
Wheel locks must be adjusted to
suit the new position.
The longer the wheel base, the
greater the stability of the
wheelchair. Turn the axle bracket
to the rear (1) in order to extend the wheel base.
CAUTION: Wheel locks must be adjusted to suit
the new position.
Options – Backrest
Adjustable Backrest
Upholstery
The sling can be adapted to any
degree of tension by adjusting the
Velcro fasteners. The padding in
the backrest can be removed
through an interior opening, allo-
wing you to cushion the backrest
according to your individual needs.
Adjustable back height
(7.77.3)
The backrest can be set to two
different back heights (41-43 cm).
Undo the screws (1) and adjust the
back to the required height.
Tighten the screws back up (see
Torque).
Half folding backrest
(7.78)
For folding the back down press
the latches (1).
CAUTION:
Make sure that the backrest
locks in correctly when it is set
upright again. When adjusting be
careful not to get your fingers
caught.
1
2
408
1
409
1
410
1
410.1
7
BREEZY ELEGANCE · Rev.A
