Idiomas disponibles
Idiomas disponibles
Once regulator i sin place, o pen the shutoffvalveinthe
gassupply line.Waita few minutes f or gasto move
through thegasline.
Check for leaks.Afterconnecting t herange tothe gas
supply, c heck the system for leaks with a manometer. If
a manometer isnotavailable, turnonthe gassupply and
usea liquidleakdetector ( orsoapandwater)at all
jointsandconnections to check for leaks.
Electrical
Requirements
120 volt, 60 Hertz, properly grounded dedicated circuit
protected by a 15 amp circuit breaker or time delay fuse.
Note: Not recommended to be installed with a Ground
Fault Interrupt (GFI).
Do not use an extension
cord with
this range.
Grounding
Instructions
IMPORTANT Please read carefully.
Do not use a flame to check for leaks
from gas connections. Checking for leaks with a flame
may result in a fire or explosion.
Tighten
all connections
as necessary to prevent gas
leakage in the range or supply line.
For personal
safety,
this appliance
must be properly
grounded.
The power cord of this appliance is equipped with a 3-
prong (grounding) plug which mates with a standard 3-
prong grounding wall receptacle (see Figure 7) to
minimize the possibility of electric shock hazard from the
appliance.
Disconnect
this range and its individuaJ
manuaJ
shutoff
valve from the gas supply piping system during
any pressure testing of that system at test pressures
greater than I/2 psig (3.5 kPa or 14" water column).
isolate the range from the gas supply
piping system
by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at test
pressures equal to or less than I/2 psig (3.5 kPa or 14"
water column).
The wall receptacle and circuit should be checked by a
qualified electrician to make sure the receptacle is
properly grounded.
Preferred Method
Grounding type
wall receptacle
Do not, under any
circumstances,
cut,
remove, or bypass
the grounding
prong.
LPIPropane
Gas Conversion
This appliance can be used with Natural gas or LP/Propane
gas. It is shipped from the factory for usewith natural gas.
If you wish to convert your range for use with LP/Propane
gas, use the supplied fixed orifices located in a bag
containing the literature marked "FOR LP/PROPANEGAS
CONVERSION." Follow the instructions packaged with
the orifices for surface, oven and broil burners
conversion.
The conversion must be performed by a qualified service
technician in accordance with the manufacturer's
instructions and all local codes and requirements. Failure
to follow these instructions could result in serious injury
or property damage. The qualified agency performing
this work assumes responsibility for the conversion.
Failure to make the appropriate
conversion can result in serious personal injury and
property damage.
Figure 7
Power supply cord with 3-
prong grounding plug.
Where a standard 2-prong wall receptacle is installed, it
is the personal responsibility and obligation
of the
consumer to have it replaced by a properly grounded 3-
prong wall receptacle.
Do not, under any circumstances, cut or remove the
third (ground)
prong from the power
cord.
Disconnect electrical supply cord from
wall receptacle before servicing cooktop.
Moving
the Appliance
for
Servicing
and Cleaning
Turn off the range line fuse or circuit breakers at the main
power source, and turn off the manual gas shut-off valve.
Make sure the range is cold. Remove the service drawer
(warmer drawer on some models) and open the oven door.
Lift the range at the front and slide it out of the cut-out
opening without creating undue strain on the flexible gas
conduit. Make sure not to pinch the flexible gas conduit at
the back of the range when replacing the unit into the cut-
out opening. Replace the drawer, close the door and
switch on the electrical power and gas to the range.
