Idiomas disponibles
Idiomas disponibles
Range
JnstalNation
Standard
Installation
1. The range cooktop overlaps the countertop
at the
sides and the range rests on the floor. The cooktop
is 31 I/2"(!,27
cm) (81 cm) wide.
2. Install base cabinets 30" (762 cm) apart. Make sure
they are level before attaching cooktop. Shave
raised countertop edge to clear 31 1/2 "(1,27 cm)
wide range top rim.
3. Install cabinet doors 31 " (78.7 cm) rain. apart so
they will not interfere with range door opening.
4. Cut out countertop
exactly as shown on page 1.
5. A backguard kit can be ordered through Sears
Service Center.
6. To provide an optimum installation, the top surface
of the countertop
must be level and flat (lie on the
same plane) around the 3 sides that are adjacent to
range cooktop. Proper adjustments to make the top
flat should be made or gaps between tile countertop
and the range cooktop may occur.
7. _
To reduce the risk of damaging your
appliance, do not handle or manipulate it by the
cooktop. Manipulate the appliance with (:are.
8. Position range in front of the cabinet opening.
9. Make sure that the cooktop which overhangs the
countertop clears the countertop. If necessary, raise
the unit by lowering tile leveling legs.
10.Leve! the range (see section I 0). The floor where the
range is to be installed must be level. Follow the
instructions under "Leveling the Range-Models
Equipped with Leveling Legs" (figure ! 5).
11. Adjust leveling legs so that the underside of the
cooktop is sitting on the countertop.
12. Carefully screw in the back leveling leg until the
cooktop overhang slightly touches the countertop.
Tile cooktop must not support the unit.
13. Then carefully screw in the front two leveling legs
(similar to ! 1) until the cooktop overhang touches
slightly the countertop.
14.1fthe range is not level, pull unit out and readjust
leveling legs, or make sure floor is level.
Installation
For 29" Cutout
Wide Opening
1. You must replace the actual side trims by new and
smaller side trims. These new side trims can be
ordered through a Sears Service Center.
2. Follow instructions supplied with new side trims for
side trim replacement.
3. Check if the countertop
is prepared for 29" cutout
wide opening in "Countertop
Preparation"
section.
4. Install range as in the "Standard
installation"
section above.
Installation
With Backguard
Tile cutout depth of (21 3/4" (55.2 cm) Min., 22 1/8"
(56.2 cm) Max.) needs to be increased to 24"(10,16
cm)
(61 cm) when installing a backguard.
Installation
With Side Panels
Install cabinet doors 31 " (78.7 cm) rain. apart so as not
to interfere with range door opening.
NOTE
Side panel, Backguard and End Panel kits can be ordered
through
Sears Parts & Repair. Call 1-800-4-MY-HOME
@.
Check Operation
Refer to the Use and Care Guide packaged with the
range for operating instructions and for care and cleaning
of your range.
Remove all packaging from the oven before testing.
9.1 Install
Burner
Bases and Burner
Caps
This range is equipped
with
sealed
burners
as shown
(see Figure
9).
Electrode
__
Figure
9
a, Unpack burner
bases and burner
caps.
b, Place burner
bases over each gas opening.
c. Make sure the burner
is properly
aligned
and leveled.
Place burner caps over appropriate
burner
bases.
NOTE: There are no burner adjustments necessary on
this range.
