Idiomas disponibles
Idiomas disponibles
EN
FR
DE
ES
IT
NL
5. Turn the tank upside down, and insert the casters on to
the four feet of the tank.
6. Ensure that they are mounted correctly. Do not over
tighten. (Fig. 5)
7. Insert the handle into the slots on the power head and
pressure into place. (Fig. 6)
8. For dry vacuum cleaning, install the supplied cartridge
fi lter and dust bag. (Fig. 7, Fig. 8)
9. For wet vacuum cleaning, install the supplied foam
fi lter. (Fig. 9)
10. Replace the top section on the tank. (Fig. 10)
11. Align the top section with the clamps and snap into
place by applying pressure until clamps click. (Fig. 10)
12. Insert the large end of the hose into the front inlet of
the tank and turn to lock. (Fig. 11)
13. Fit the required accessory on to the suction tube. (Fig.
12)
OPERATION
DRY VACUUMING
WARNING
Ensure that you read, understand, and apply the
safety instructions.
Reminder: DO NOT vacuum hazardous substances.
The use of an incorrect dust bag will invalidate the
warranty.
1. Ensure that the power cord is disconnected from the
power outlet.
2. Ensure that the cartridge fi lter is completely mounted.
3. Ensure that the fi lter is inserted all the way. (Fig. 13)
Verify that the dust bag is installed to the inside of the
tank. (Fig. 8)
4. Replace the top section on the tank, and secure it in
place using the clamps. (Fig. 10)
5. Insert the larger end of the hose into the front inlet
on the tank and lock it in place. Push the required
attachment on to the free end of the hose or extension.
(Fig. 12)
6. Plug the power cord in to the power outlet.
7. Turn the motor on by fl ipping the switch to the 'I' (ON)
position. (Fig. 14)
8. Once you have fi nished vacuuming, fl ip the switch to
the 'O' (OFF) position and unplug the power cord from
the power outlet. (Fig. 15)
WARNING
DO NOT USE THE CARTRIDGE FILTER FOR WET OR
SHARP MATERIALS.
DO NOT USE DUST BAG FOR LIQUID VACUUMING.
PT
DA
SV
FI
NO
RU
English
PL
CS
HU
RO
LV
LT
WET VACUUMING
WARNING
1. Ensure that you read, understand, and apply the
safety instructions.
Reminder: DO NOT vacuum hazardous substances.
2. Ensure that the power cord is disconnected from the
power outlet.
Ensure that the tank is clean and free of dust and dirt.
3. Remove the cartridge fi lter and dust bag, and install
a foam fi lter over the fi lter basket and place the top
section back on the tank. (Fig. 9)
DO NOT use the cartridge filter for wet or sharp
materials.
4. Fit the desired nozzle to the vacuum hose. (Fig. 12)
5. Ensure that the switch is in the 'O' (OFF) position
before plugging the power cord into the power outlet.
6. Turn the motor on by fl ipping the switch to the "I" (ON)
position. (Fig. 14)
7. After use, fl ip the switch to the·"O" position (Fig. 15)
and unplug the power cord, then empty and dry the
tank. (Fig. 16, Fig. 17)
WARNING
The foam filter must be removed after wet vacuuming,
and a cartridge filter must be installed before dry
vacuuming again.
IMPORTANT!
When vacuuming large quantities of liquids, do not
immerse the nozzle completely in the liquid; leave a gap
at the tip of the nozzle opening to allow air infl ow.
The machine is fi tted with a fl oat valve that stops the
suction action when the container reaches its maximum
capacity. You will notice an increase in motor speed.
When this happens, turn off the machine, disconnect
from power supply, and drain the liquid into a suitable
receptacle or drain. To continue vacuuming, refi t the
container with the drain cap. After wet vacuuming, turn the
machine off and remove plug from power supply.
Empty the container, clean and dry the inside and outside
before storage.
BLOWER OPERATION
This Wet/Dry Vac has blowing capabilities.
To use the blower feature follow the instructions listed.
WARNING
Always wear safety goggles before using blower.
Keep bystanders clear from blowing debris.
Wear a dust mask if blowing creates dust that might be
inhaled.
12
ET
HR
SL
SK
BG
UK
TR
EL
