Idiomas disponibles
Idiomas disponibles
5.
Using a cordless drill, drill a 1/4" hole in the cold water pipe
you have selected.
A. Cold
water
pipe
B. Pipe clamp
C. Copper
tubing
D. Compression
nut
E. Compression
sleeve
F. Shutoff
valve
G. Packing
nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the 1/4" (6.35 ram)
drilled hole in the water pipe and that the washer is under
the pipe clamp. Tighten the packing
nut. Tighten the pipe
clamp screws slowly and evenly so washer makes a
watertight
seal. Do not overtighten
or you may crush the
copper tubing.
7. Slip the compression
sleeve and compression nut onto the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression
nut onto outlet end with adjustable
wrench. Do not
overtighten.
8. Place the free end of the tubing in a container or sink, and
turn ON the main water supply. Flush the tubing until water
is clear. Turn OFF the shutoff valve on the water pipe. Coil
the copper tubing.
Style 2
1.
Unplug
refrigerator
or disconnect
power.
2.
Remove
and discard
the black
nylon
plug from
the gray
water
tube
on the rear of the refrigerator.
3.
Thread
the provided
nut onto
the water
valve
as shown.
NOTE:
Tighten
the nut by hand.
Then tighten
it with
a
wrench
two more turns.
Do not overtighten.
A
Ill
B
Connect to Refrigerator
Style I
1. Unplug refrigerator or disconnect power.
2. Attach the copper tube to the valve inlet using a
compression nut and sleeve as shown. Tighten the
compression nut. Do not overtighten.
3. Use the tube clamp on the back of the refrigerator
to secure
the tubing to the refrigerator
as shown. This will help avoid
damage to the tubing when the refrigerator
is pushed back
against the wall.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
A
.............
B
C
D
E
A. Tube clamp
B. Tube clamp
screw
C. Copper
tubing
D, Compression
nut
E. Valve
inlet
6.
On models with ice makers, the ice maker is equipped with
a built-in water strainer. If your water conditions require a
second water strainer, install it in the ¢/4" (6.35 mm) water
line at either tube connection. Obtain
a water strainer from
your nearest appliance
dealer.
Style 2
1.
Unplug
refrigerator
or disconnect
power.
2.
Remove
and discard
the black
nylon
plug from
the gray
water
tube
on the rear of the refrigerator.
3.
If the gray
water
tube
supplied
with
the refrigerator
is not
long enough,
a 1/4" x ¢/4" (6.35
mm x 6.35
mm) coupling
is
needed
in order
to connect
the water
tubing
to an existing
household
water
line. Thread
the provided
nut onto the
coupling
on the end of the copper
tubing.
NOTE:
Tighten
the nut by hand.
Then tighten
it with
a
wrench
two more turns.
Do not overtighten.
4.
5.
A. Bulb
B. Nut (provided)
Turn shutoff
valve
ON.
Check
for leaks.
Tighten
any nuts or connections
(including
connections
at the valve)
that leak.
4.
5.
A
B
C
D
E
F
G
A. Refrigerator
water tubing
B. Nut (provided)
C. Bulb
D. Coupling
(provided)
Turn shutoff
valve
ON.
Check
for leaks. Tighten
any nuts or connections
(including
connections
at the valve)
that leak.
E. Ferrule (purchased)
F. Nut (purchased)
G.Household
water line
10
