Idiomas disponibles
Idiomas disponibles
INSTALLATION
REQUIREMENTS
Assemble the necessary tools and supplies before beginning the
washer installation. The parts supplied are in the washer basket.
Tools needed for connecting
the drain hose and
water inlet hoses:
•
Pliers that open to 19/16 in. (3.95 cm)
•
Flashlight (optional)
Parts supplied:
3
4
5
1. Drain hose
2. Silver, double-wire
hose clamp
(for the bottom of the drain hose)
3. Yellow, single-wire
hose clamp
(for the top of the drain hose)
4. Water inlet hoses (2)
5. Flat water inlet hose washers (4)
Tools needed for securing the drain hose and
leveling the washer.
•
Adjustable or open end wrench %6in. (14 mm)
•
Level
•
Wood block
•
Ruler or measuring tape
Parts supplied:
1
2
1. Shipping strap with fastener
2. Front leveling feet with nuts (2)
Alternate
Parts
Parts listed are available from your local Sears store or Sears
Service Center. For further information, please call 1-800-4-MY-
HOME ® (1-800-469-4663}.
If You Have:
You Will Need to Buy:
Laundry tub or
Sump pump system (if not already
standpipe taller
available)
than 96 in. (2.4 m)
1 in. (2.5 cm)
2 in. (5 cm) diameter to 1 in. (2.5 cm)
diameter
diameter standpipe adapter, Part No.
standpipe
3363920
Overhead sewer
Standard 20 gaL (76 L) 39 in. (99 cm) tall
drain tub or utility sink, sump pump and
connectors
(available from local
plumbing suppliers)
Floor drain
Siphon break, Part Number 285320;
additional drain hose, Part Number
3357090 and connector kit,
Part Number 285442
Water faucets
2 longer water fill hoses:
beyond reach of
6 ft (1.8 m) Part Number 76314,
fill hoses
10 ft (3.0 m) Part Number 350008
Drain hose too
Drain hose, Part No. 388423 and hose
short
kit, Part No. 285442
Drain hose that is
Hose kit, Part No. 285442
too long
Lint clogged drain
Drain protector, Part No. 367031
Selecting the proper location for your washer improves
performance
and minimizes noise and possible washer "walk."
Your washer can be installed in a basement, laundry room,
closet, or recessed area. (See "Drain System.")
IMPORTANT:
Do not install or store the washer where it will be
exposed to the weather.
Proper installation is your responsibility.
You will need:
•
A water heater set to deliver 120°F (49°C) water to the
washer.
A grounded electrical outlet located within 4 ft (1.2 m) of
where the power cord is attached to the back of the washer.
(See "Electrical Requirements.")
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of 5-100 psi
(34.5-690 kPa). Washers with triple dispensers require
26-100 psi (138-690 kPa) for best performance.
A level floor with a maximum slope of 1 in. (2.5 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
•
A sturdy floor to support the washer weight (washer, water
and load) of 315 Ibs (143 kgs).
Do not store or operate your washer in temperatures
at or below
32°F (0°C). Some water can remain in the washer and can cause
damage in low temperatures.
See "Washer Care" for winterizing
information.
