Idiomas disponibles
Idiomas disponibles
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e.g.,
against continuous intense sunlight, fire,
water, and moisture. Danger of explosion.
In case of damage and improper use of the
battery, vapours may be emitted. Ventilate
the area and seek medical help in case of com-
plaints. The vapours can irritate the respiratory system.
Use the battery only in conjunction with your
Würth power tool. This measure alone protects the
battery against dangerous overload.
The battery can be damaged by pointed objects
such as nails or screwdrivers or by force
applied externally. An internal short circuit can occur
and the battery can burn, smoke, explode or overheat.
Wear protective gloves when changing appli-
cation tools/accessories. Application tools/acces-
sories become hot after prolonged usage.
Do not scrape wetted materials (e.g. wallpa-
per) or on moist surfaces. Penetration of water into
the machine increases the risk of an electric shock.
Do not treat the surface to be worked with sol-
vent-containing fluids. Materials being warmed up
by the scraping can cause toxic vapours to develop.
Exercise extreme caution when handling the
scraper. The accessory is very sharp; danger of injury.
Use only original Würth accessories.
Intended Use
The machine is intended for sawing and cutting wooden mate-
rials, plastic, gypsum, non-ferrous metals and fastening ele-
ments (e.g. nails, staples). It is also suitable for dry sanding
and scraping of small surfaces. It is especially suitable for
working close to edges and for flush cutting.
For damage caused by usage other than intended, the user is
responsible.
Product Features
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
The numbering of the product features refers to the illustration
of the power tool on the graphics page.
1 Battery unlocking button
2 Battery pack
3 Button for charge-control indicator
4 Battery charge-control indicator
5 On/Off switch
6 Thumbwheel for orbit frequency preselection
7 Venting slots
8 Tool holder
9 Handle (insulated gripping surface)
10 Sanding plate
11 Clamping bolt with spring washer
12 Hex key
13 Sanding sheet*
14 Adapter for tool holder
15 Saw blade*
*Some accessories shown or described are not part of
the standard delivery scope of the product.
Tool Specifications
Cordless Multi Cutter
Art. No.
Rated voltage
No-load speed n
0
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
1)
– during operation
and during
storage
Recommended batteries
Recommended chargers
1) Limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 91 dB(A); Sound power level
102 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
h
determined according to EN 60745:
2
Sanding: a
=2.6 m/s
, K=1.5 m/s
h
Cutting with plunge cut saw blade: a
2
K=1.5 m/s
Cutting with segmental saw blade: a
2
K=1.8 m/s
Scraping: a
=17.3 m/s
h
0700 282 X
V=
-1
min
5000–20000
°
kg
°C
°C
0700 996 2XX
0700 896 XXX
(triax vector sum) and uncertainty K
2
=13.1 m/s
h
=12.2 m/s
h
2
2
, K=1.6 m/s
.
EMS 10-A
10.8
1.4
1.0
0...+45
–20...+50
2
,
2
,
13
