Metabo CED 125 Manual Original página 10

en ENGLISH
Do not use bonded discs.
Use elastic cushioning layers if they have been
supplied with the grinding media and if required.
Observe the specifications of the accessory
manufacturer! Protect the accessories from grease
and physical impact.
Accessories must be stored and handled with care
in accordance with the manufacturer's instructions.
The workpiece must lay flat and be secured against
slipping, e.g. using clamps. Large workpieces must
be sufficiently supported.
Damaged, eccentric or vibrating tools must not be
used.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Avoid damage to gas or water pipes, electrical
cables and load-bearing walls (static).
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
Read the operating instructions supplied with the
installed angle grinder.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
Prior to each use, check if there are parts missing,
worn, broken, torn or damaged. Do not use
defective or incomplete guard.
Reduce dust exposure:
Some dust created by using this power tool
may contain chemicals known to cause
cancer, allergic reaction, respiratory disease, birth
defects or other reproductive harm. Some
examples of these chemicals are: Lead from lead-
based paints, crystalline silica from bricks and
cement and other masonry products, Arsenic and
chromium from chemically-treated lumber, hard
wood like oak or beech, Asbestos.
The risk from these exposures depends on how
long you or bystanders are being exposed.
Do not let particles enter the body.
To reduce your exposure to these chemicals: work
in a well ventilated area, and work with approved
safety equipment, such as dust masks that are
specially designed to filter out microscopic
particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers
10
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing stirs up dust
- Vacuum or wash the protective clothing Do not
blow, beat or brush
4. Overview
See page 2.
1 Push machine only in direction of arrow
2 Side handle (of the angle grinder) *
3 Unlocking lever
4 Spindle locking button (of the angle grinder) *
5 Extractor connection piece
6 Clamping screw (cutting depth limitation)
7 Castors (only for CED 125 Plus ) *
8 Guide rail adapter for attachment to the Metabo
guide rail (only for CED 125 Plus) *
9 Guard (complete)
10 Slider (for dismantling the guard)
11 Base part
12 Guard
13 Lever (of the angle grinder) *
14 Clamping screw
15 2-hole spanner
16 2-hole adjusting nut
17 Diamond cutting disc *
18 Spacer sleeve
19 Support flange (of the angle grinder) *
20 Spindle (of the angle grinder) *
* not in scope of delivery/ depends on equipment
5. Commissioning
5.1 Attachguard at the angle grinder
See page 2, fig. C.
- Dismantle extraction guard (12) and base part
(11)as described in chapter 6.1.
- Push and hold the lever (13). Attach the angle
grinder in the shown position to the extraction
guard (12).
- Release the lever and turn the extraction guard
until the lever (13) engages.
- Make sure that the guard is placed securely: The
lever must engage and you should not be able to
turn the extraction guard.
- Tighten the clamping screw (14) if required.
- Assemble guard (12) and base part (11) as
described in chapter 6.1.
- Attach the side handle (2). See Section 5.2
(Disassemble in reverse order.)
5.2 Attaching the additional handle
Always work with the additional handle (2)
attached!
- Remove side handle (2) from the angle grinder
and screw in firmly on the left or right side of the
extraction guard (12).